Page 1
Quick Start for Hardware Installation Avaya P332MF Stackable Switch 10-300712 Issue 1 September 2005...
Page 2
Copyright 2005, Avaya Inc. All Rights Reserved Notice Every effort was made to ensure that the information in this document was complete and accurate at the time of printing. However, information is subject to change. Warranty Avaya Inc. provides a limited warranty on this product. Refer to your sales agreement to establish the terms of the limited warranty.
Chapter 1: Before you Start Before you install your Avaya Switch, prepare all the information, resources, and tools that you need during the installation process. Good preparation ensures a smooth installation with the least amount of interruption. WARNING: ONLY TRAINED AND QUALIFIED PERSONNEL SHOULD BE ALLOWED TO WARNING: INSTALL OR REPLACE THIS EQUIPMENT.
Air can flow freely around all sides of the chassis. ● The vents on the sides of the chassis are not blocked. ● 6 Quick Start for Hardware Installation: P332MF Stackable Switch Table Prepare these tools Phillips head screwdriver http://...
Page 7
The environmental conditions match the requirements listed in ● Table 2: Environmental Requirements Condition Ambient temperature Relative humidity Weight support The power source matches the specifications shown in ● Table 3: Power Requirements Power consumption AC Input voltage AC Input current DC Input voltage DC Input current See the Avaya P333T User’s Guide, 03-300148, for additional information on environmental...
It is highly recommended to upgrade/downgrade before connecting the added Tip: box to an existing stack. - Ensure switches of the same type have the same firmware version 8 Quick Start for Hardware Installation: P332MF Stackable Switch to see which firmware versions can be used in mixed stacks.
Page 9
Table 4: Firmware Versions Matrix Required version Stack without C360 Switch 3.11 P333T 3.11.0 P334T 3.11.0 P333R 3.11.0 P333R-LB 3.11.0 P332MF 3.11.0 P333T-PWR 3.11.0 G700 3.11.0 P334T-ML 3.11.16 P332G-ML 3.11.15 P332GT-ML 3.11.15 C363T C364T C363T-PWR C364T-PWR Note: Position the C360 switches either at the top or bottom of the stack to ensure Note: mechanical stability.
P330. Connect the strap to an approved ground, such as an unpainted metal surface. Equipment Open the box that contains the P330, and ensure that it contains the following components and accessories: One Avaya P332MF Switch. ● One Accessory Kit that contains: ● One 115V 3 Wire...
Avaya P330 Documentation and Utilities CD (see detail below) ● Avaya Communication Warranty and License Agreement ● Avaya P330 Documentation and Utilities CD The CD contains the latest User's Guides for the Avaya P330 stackable switches and files for use with the Embedded Web Manager. User's Guides ●...
Page 16
Unpack the Device 16 Quick Start for Hardware Installation: P332MF Stackable Switch...
Chapter 3: Mount the Device You can mount the P330 in a rack. The P330 chassis fits in most standard 19-inch racks. It is 2U (3.5”, 88 mm) high. Before you Install the P330 in a Rack Disconnect all cables from the unit before proceeding with the rack installation. ●...
Page 18
3. Secure the unit to the rack, taking care not to overtighten the screws. 4. Snap closed the hinged ends of the front panel. Tip: You can now safely connect the cables to the unit. Tip: # Quick Start for Hardware Installation: P332MF Stackable Switch 11 12 Hspd OPR PWR CONSOLE...
Chapter 4: Power Up Connecting the P330 to the main electrical supply provides power to the switch. VOLTAGE ALERT: To isolate the switch completely, you must disconnect all power connections: AC VOLTAGE ALERT: plug or DC terminal block and DC BUPS power. P330 AC version 1.
The unit powers up and performs a self test procedure. The LEDs flash at regular intervals after the self-test procedure is completed successfully. VOLTAGE ALERT: The proper wiring sequence is: VOLTAGE ALERT: 1. ground to ground 2. positive to positive 20 Quick Start for Hardware Installation: P332MF Stackable Switch...
Page 21
P330 DC version 3. negative to negative WARNING: Always connect the ground wire first and disconnect it last. WARNING: Issue 1 September 2005...
Page 22
Power Up 22 Quick Start for Hardware Installation: P332MF Stackable Switch...
Chapter 5: Prepare for Configuration This chapter provides information on preparing the P330 for configuration, and discusses the following topics: Establishing a Console Connection ● Assigning a P330 IP Stack Address ● Establishing a Telnet Connection ● Configuring the Switch ●...
2. When prompted for a Login Name, enter the default name root 3. When you are prompted for a password, enter the password root. You are now in Supervisor Level. 24 Quick Start for Hardware Installation: P332MF Stackable Switch...
4. At the prompt, type: set interface inband <vlan> <ip_address> <netmask> Replace <vlan>, <ip_address> and <netmask> with the VLAN, IP address, and net mask of the stack. 5. Press Enter to save the IP address and net mask. 6. At the prompt, type reset. Type y and press Enter to reset the stack. After the Reset, log in again as described above.
3. After the Reset, perform login again as described above. - The P330-N(super)# prompt appears. 4. Type set ip route <destination> <gateway>, replacing <destination> and <gateway> with the destination and gateway IP addresses. 26 Quick Start for Hardware Installation: P332MF Stackable Switch...
5. Press Enter to save the destination and gateway IP addresses. Avaya P330 Default Settings If you wish to change the default parameters shown and configure the mandatory parameters, we recommend that you use the Command Line Interface (CLI). For further information, please refer to Chapter 6 of the Avaya P330 User’s Guide. The default settings for the Avaya P330 switch and its ports are determined by the Avaya P330 firmware.
Page 28
Port VLAN ID Tagging mode Port priority Tip: Functions operate in their default settings unless configured otherwise. Tip: 28 Quick Start for Hardware Installation: P332MF Stackable Switch Default Setting 10/100-TX ports: Auto-negotiation ● 100Base-FXports:100 Mbps full duplex ● 1000Base-X ports: 1000 Mbps full duplex ●...
Chapter 6: Device Manager This chapter describes the installation procedures for the Device Manager of the Avaya P330. Overview The Device Manager provides the following: Managing and monitoring Power over Ethernet. ● Device Configuration - Viewing and modifying the different device configurations. ●...
2. Enter the URL of the switch in the format http://aaa.bbb.ccc.ddd where aaa.bbb.ccc.ddd is the inband or outband interface IP address of the switch. 30 Quick Start for Hardware Installation: P332MF Stackable Switch Use the following command... set snmp retries...
Page 31
- The user name is “root”. - The default password for read-only access is “root”. - The default passwords for read-write access is “root”. Note: The P330 Device Manager passwords are the same as those of the CLI. If you Note: change the passwords of the CLI then those passwords become active for the Device Manager as well.
To install from the P330 Documentation and Utilities CD: 1. Close all unnecessary applications on your PC. 2. Insert the Avaya P330 Documentation and Utilities CD in the CD drive. 3. Open Windows Explorer. 32 Quick Start for Hardware Installation: P332MF Stackable Switch Installing the Java Plug-in).
4. Browse to the embweb-aux-files\ folder on the CD. 5. Double-click plugin_a_b_c.exe (a, b and c are the version numbers of the plug-in). 6. Follow the on-screen instructions. Install from the Avaya Web Site Click the link in the Welcome page labelled “Retrieve it from here”. Install from your Local Web Site Click the appropriate link in the Welcome page.
Device Manager Documentation The Device Manager comes with a detailed User’s Guide including a Glossary of Terms and an overview of Data Communications concepts. 34 Quick Start for Hardware Installation: P332MF Stackable Switch...