Mitsubishi Electric MELSEC iQ-F FX5 User Manual page 325

Error Error name Error details and cause
code
1825H Write during RUN • Writing during RUN (change or deletion)
error (axis 5) is performed on an instruction being
executed.
1826H Write during RUN • Writing during RUN (change or deletion)
error (axis 6) is performed on an instruction being
executed.
1827H Write during RUN • Writing during RUN (change or deletion)
error (axis 7) is performed on an instruction being
executed.
1828H Write during RUN • Writing during RUN (change or deletion)
error (axis 8) is performed on an instruction being
executed.
1829H Write during RUN • Writing during RUN (change or deletion)
error (axis 9) is performed on an instruction being
executed.
1830H Write during RUN • Writing during RUN (change or deletion)
error (axis 10) is performed on an instruction being
executed.
1831H Write during RUN • Writing during RUN (change or deletion)
error (axis 11) is performed on an instruction being
executed.
1832H Write during RUN • Writing during RUN (change or deletion)
error (axis 12) is performed on an instruction being
executed.
1900H Constant scan • The scan time exceeded the constant
time error scan setting value.
Action
• Verify that the writing during RUN (change or
deletion) is performed on an instruction
being executed.
• If the writing is executed during an ongoing
RUN, after confirming that the pulse output
is not occurring, turn OFF  ON the driving
contact point to start the operation of the
positioning instruction.
• Verify that the writing during RUN (change or
deletion) is performed on an instruction
being executed.
• If the writing is executed during an ongoing
RUN, after confirming that the pulse output
is not occurring, turn OFF  ON the driving
contact point to start the operation of the
positioning instruction.
• Verify that the writing during RUN (change or
deletion) is performed on an instruction
being executed.
• If the writing is executed during an ongoing
RUN, after confirming that the pulse output
is not occurring, turn OFF  ON the driving
contact point to start the operation of the
positioning instruction.
• Verify that the writing during RUN (change or
deletion) is performed on an instruction
being executed.
• If the writing is executed during an ongoing
RUN, after confirming that the pulse output
is not occurring, turn OFF  ON the driving
contact point to start the operation of the
positioning instruction.
• Verify that the writing during RUN (change or
deletion) is performed on an instruction
being executed.
• If the writing is executed during an ongoing
RUN, after confirming that the pulse output
is not occurring, turn OFF  ON the driving
contact point to start the operation of the
positioning instruction.
• Verify that the writing during RUN (change or
deletion) is performed on an instruction
being executed.
• If the writing is executed during an ongoing
RUN, after confirming that the pulse output
is not occurring, turn OFF  ON the driving
contact point to start the operation of the
positioning instruction.
• Verify that the writing during RUN (change or
deletion) is performed on an instruction
being executed.
• If the writing is executed during an ongoing
RUN, after confirming that the pulse output
is not occurring, turn OFF  ON the driving
contact point to start the operation of the
positioning instruction.
• Verify that the writing during RUN (change or
deletion) is performed on an instruction
being executed.
• If the writing is executed during an ongoing
RUN, after confirming that the pulse output
is not occurring, turn OFF  ON the driving
contact point to start the operation of the
positioning instruction.
• Check and correct the constant scan time
setting. Recheck the setting time of the
constant scan.
Detailed Diagnostic
information timing
Error location At END
information instruction
and system execution
configuration
information
Error location At END
information instruction
and system execution
configuration
information
Error location At END
information instruction
and system execution
configuration
information
Error location At END
information instruction
and system execution
configuration
information
Error location At END
information instruction
and system execution
configuration
information
Error location At END
information instruction
and system execution
configuration
information
Error location At END
information instruction
and system execution
configuration
information
Error location At END
information instruction
and system execution
configuration
information
Time At END
information instruction
execution
APPENDIX
323
Appendix 3 Error Code
A