HME Wireless 6000 Installation Instructions Manual page 47

Outside Speaker
To DM1 Microphone
IMPORTANT
MICROPHONE AND SPEAKER
MUST USE SEPARATE CABLES
To Timer System
Positive Vehicle Detect Signal (+11V Minimum)
Negative Vehicle Detect Signal
NOTE: If using the Internal Message Repeater,
do not use J3 pins 6 & 7 for Greet.
See ALTERNATE GREET WIRING.
From External Detector
Negative Vehicle Detect Signal
Positive Vehicle Detect Signal (+11V Minimum)
(When not using optional VDB)
To Backup System
Negative Vehicle Detect Signal
Positive Vehicle Detect Signal (+11V Minimum)
Speaker/Microphone
Speaker/Microphone
Base station interconnect cable connections for
dual-lane systems not using a mode switch
Vehicle Detect In
Vehicle Detect Out
/A2 - Talk
Connections at /B2 - Talk
Car 2
J26 in Secondary
Ground
Base Station
Transmitter Audio A2
Ground
Receiver Audio A2
Receiver Audio B2 (B1 + B2)
* NOTE: If using a mode switch between two base stations, the
vehicle detect wires and a ground wire at each end of the base
station interconnect cable must be broken out of the cable and
connected to J22 in the Primary Base Station and J26 in the
Secondary Base Station as shown below. If no mode switch is used,
the vehicle detect wires will remain connected as shown above.
Base station interconnect cable connections for
dual-lane systems if using a mode switch
MS1000 Mode Switch
(optional with dual-lane systems)
VEH DETECT OUT
1
NOT USED
2
GROUND Shld
3
VEH DETECT IN
4
S1
VEH DETECT OUT
NC NC NC NC
4
NOT USED
3
GROUND
2
VEH DETECT IN
1
Figure E-10.
to J2, 1 & 2
In this configuration,
to J1, 4
White
this switch must be
to J1, 3
Shield
to J1, 2
Black
to J1, 1
Red
to J3, 10
to J3, 9
Ground
to J3, 8
to J3, 7
Greet
to J3, 6
Greet
to J3, 5
to J3, 4
Ground
to J3, 3
to J4, 3
to J4, 4
Ground
to J4, 5
to J4, 7
to J4, 8
NOTE: J22, 1 to J26, 1 J22, 2 to J26, 2 etc. ; ;
*
1
2 *
3
4
5
6 *
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10
7
8
J26
9
10
2
24
J28
1
Transceiver
Board
8
K1
ON
OFF
Primary
K2
Base
2
Shield
6 J22
1
Secondary Ant 2
Ant 1
Base
1
2 J26
6
44
OUT .
S1
J5
J6 J1 J2
J4
J3
Switcher
Board
optional
S2
TB1
1 2 3 4 5 6 7 8 9 10
J5
J22 J25
1 2 3 4 5
J18
S2
R9
R368
R348
R320
R292
R42 R42
R43 R43
JP2 JP1
DS7
K4
DS6
DS5
DS4
K3
DS10
DS9
DS8
DS2
DS3
TB1
Vehicle
Detector
Alternate Greet Wiring
Board
Connect timer ground to base audio J2, 1.
(VDB)
Connect an unused Vehicle Detect input
optional (1-6) to base audio J2, 2. Assign the
P1
Vehicle (1-6) as GREET and configure
S1
for negative detection.
to J2, 2
to J2, 3
to J2, 4
to J2, 6=gn, 7=wh & 8=shld
to J29, 1 & 2
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2
J30 J2 J29
JP4
JP3
JP5
J10
Audio
J15
Circuit Board
J9
S6
S1
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 1 2 3 4
IMPORTANT
Before completing this installation,
be certain all DIP switches,
jumpers and adjustments
are set appropriately.
To Underground Loop
"A" Decode (Active Low)
To Message Repeater
Isolated Vehicle Detect Signal
Isolated Vehicle Detect Ground
Grill
Speaker
(optional)
16.5 VAC
Adapter
J9 - Input/Output
to J9, 1
Early Warning In (Active Low)
to J9, 2
Ground
to J9, 3
Service Window In (Active Low)
to J9, 4
Alert In Ground
to J9, 5
Alert In (+12V From System 30 Timer)
Wiring Diagram for Alert Input
other than from Timer
Relay
Relay activated by
some other device
N/O Common
J9
J30
Wiring Diagram
Wireless 6000, Full -Duplex
with VDB and Switcher Board
and DM1 Microphone