Wiring Diagram, Wireless 6000, Half-Duplex With Vdb And Switcher Board - HME Wireless 6000 Installation Instructions Manual

Outside
to J2, 3, 4 & 5 (3 is for shield)
Speaker/
Microphone
To Timer System
Positive Vehicle Detect Signal (+11V Minimum)
Negative Vehicle Detect Signal
NOTE: If using the Internal Message Repeater,
do not use J3 pins 6 & 7 for Greet.
See ALTERNATE GREET WIRING.
From External Detector
Negative Vehicle Detect Signal
Positive Vehicle Detect Signal (+11V Minimum)
(When not using optional VDB)
To Backup System
Negative Vehicle Detect Signal
Positive Vehicle Detect Signal (+11V Minimum)
Speaker/Microphone
Speaker/Microphone
Base station interconnect cable connections for
dual-lane systems not using a mode switch
Vehicle Detect In
Vehicle Detect Out
/A2 - Talk
Connections at /B2 - Talk
J26 in Secondary
Ground
Base Station
Transmitter Audio A2
Ground
Receiver Audio A2
Receiver Audio B2 (B1 + B2)
* NOTE: If using a mode switch between two base stations, the
vehicle detect wires and a ground wire at each end of the base
station interconnect cable must be broken out of the cable and
connected to J22 in the Primary Base Station and J26 in the
Secondary Base Station as shown below. If no mode switch is used,
the vehicle detect wires will remain connected as shown above.
Base station interconnect cable connections for
dual-lane systems if using a mode switch
MS1000 Mode Switch
(optional with dual-lane systems)
VEH DETECT OUT
1
NOT USED
2
GROUND
Shld
3
VEH DETECT IN
4
S1
VEH DETECT OUT
NC NC NC NC
4
NOT USED
3
GROUND
2
VEH DETECT IN
1
Figure 21.
to J3, 10
to J3, 9
Ground
to J3, 8
to J3, 7
Greet
to J3, 6
Greet
to J3, 5
to J3, 4
Ground
to J3, 3
to J4, 3
to J4, 4
Ground
to J4, 5
to J4, 7
to J4, 8
NOTE: J22, 1 to J26, 1 J22, 2 to J26, 2 etc. ;
1 *
2 *
3
4
5
Car 2
6 *
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10
7
8
J26
9
10
2
J28
1
Transceiver
Board
8
K1
ON
OFF
Primary
K2
Base
2
Shield
J22
6
1
Secondary
Ant 2
Ant 1
Base
1
2 J26
6
26
S1
J5
J1 J2
J6
J4
Switcher
Board
optional
J3
S2
TB1
;
1 2 3 4 5 6 7 8 9 10
J22 J25
24
1 2 3 4 5
J18
S2
R9
R368
R348
R320
R292
JP2 JP1
DS7
K4
DS6
DS5
DS4
K3
DS10
DS9
DS8
DS2
DS3
TB1
Vehicle
Detector
Board
(VDB)
optional
P1
S1
to J2, 6=gn, 7=wh & 8=shld
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2
J5
J30 J2 J29
R42 R42
JP4
R43 R43
JP3
JP5
J10
Audio
J15
Circuit Board
J9
S1 S6
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 1 2 3 4
IMPORTANT
Before completing this installation,
be certain all DIP switches,
jumpers and adjustments
are set appropriately.
To Underground Loop
Alternate Greet Wiring
Connect timer ground to base audio J2, 1.
Connect an unused Vehicle Detect input
(1-6) to base audio J2, 2. Assign the
Vehicle (1-6) as GREET and configure
for negative detection.
to J2, 2 "A" Decode (Active Low)
To Message Repeater
to J2, 3 Isolated Vehicle Detect Signal
to J2, 4 Isolated Vehicle Detect Ground
Grill
Speaker
to J29, 1 & 2
(optional)
16.5 VAC
Adapter
J9 - Input/Output
to J9, 1
Early Warning In (Active Low)
to J9, 2
Ground
to J9, 3
Service Window In (Active Low)
to J9, 4
Alert In Ground
to J9, 5
Alert In (+12V From System 30 Timer)
Wiring Diagram for Alert Input
other than from Timer
Relay
Relay activated by
some other device
N/O Common
J9 J30
Wiring Diagram
Wireless 6000, Half -Duplex
with VDB and Switcher Board