Table 13-6 Trips - Emerson Quantum MP User Manual

Safety Product Mechanical
Information Information Installation
di08
Current magnitude
{0.43, 4.01}
RO Uni FI
0 to DRIVE_CURRENT_MAX

A
The current feedback signal is derived from internal current
transformers. It is used for closed loop control and indication of the
armature current, and to initiate motor protection.
di09
Field current feedback
{0.44, 5.56}
RO Bi FI

±50.00A
Indicates the field current feedback in 0.01 amperes.
di10
Armature voltage
{0.45, 5.02}
RO Bi FI
±ARMATURE_VOLTAGE_

MAX V
The average measured DC output voltage seen across the drive A1 and
A2 terminals or the average measured DC output voltage seen across
the motor. Selected by Pr 5.14.
The armature voltage feedback has a resolution of 10-bit plus sign.
di11
Reference enabled indicator
{0.46, 1.11}
di12
Reverse selected indicator
{0.47, 1.13}
di13
Jog selected indicator
{0.48, 1.14}
RO Bit

OFF (0) or On (1)
These parameters are controlled by the drive sequencer as defined in
Menu 6. They select the appropriate reference as commanded by the
drive logic. di11 (Pr 0.46, 1.11) will be active if a run command is given,
the drive is enabled and the drive is ok. This parameter can be used as
an interlock in a Onboard PLC or SM-Applications program to show that
the drive is able to respond to a speed or torque demand.
di14
Software version
{0.49, 11.29}
RO Uni

1.00 to 99.99
The parameter displays the software version of the drive.
Quantum MP User Guide
Issue: A4
Electrical Getting Basic
Installation Started parameters
NC PT

NC PT

NC PT

NC PT

NC PT

www.emersonct.com
Running the SMARTCARD
Optimization
Motor Operation
6.1.4 Trips
tr01
Trip 0
{0.51, 10.20}
tr02
Trip 1
{0.52, 10.21}
tr03
Trip 2
{0.53, 10.22}
tr04
Trip 3
{0.54, 10.23}
tr05
Trip 4
{0.55, 10.24}
tr06
Trip 5
{0.56, 10.25}
tr07
Trip 6
{0.57, 10.26}
tr08
Trip 7
{0.58, 10.27}
tr09
Trip 8
{0.59, 10.28}
tr10
Trip 9
{0.60, 10.29}
RO Txt

0 to 229
Contains the last 10 drive trips. tr01 (Pr 0.51, 10.20) is the most recent
trip and tr10 (Pr 0.60, 10.29) the oldest. When a new trip occurs all the
parameters move down one, the current trip is put in tr01 (Pr 0.51,
10.20) and the oldest trip is lost from the bottom of the log. Descriptions
of the trips are given in Table 13-1 on page 157. All trips are stored,
including HF trips numbered from 20 to 29. (HF trips with numbers from
1 to 16 are not stored in the trip log.) Any trip can be initiated by the
actions described or by writing the relevant trip number to Pr 10.38. If
any trips shown as user trips are initiated the trip string is "txxx", where
xxx is the trip number.
6.1.5 Speed loop
SP01
(Kp1) Speed controller proportional gains
{0.61, 3.10}
RW Uni

0.0000 to 6.5535 (1 / (rad/s))
SP01 (Pr 0.61/3.10) operates in the feed-forward path of the speed-
control loop in the drive. See Figure 11-3 on page 104 for a schematic of
the speed controller. For information on setting up the speed controller
gains, refer to Chapter 8 Optimization on page 78.
SP02
(Ki1) Speed controller integral gains
{0.62, 3.11}
RW Uni

0.00 to 655.35 (s / (rad/s))
SP02 (Pr 0.62, 3.11) operates in the feed-forward path of the speed-
control loop in the drive. See Figure 11-3 on page 104 for a schematic of
the speed controller. For information on setting up the speed controller
gains, refer to Chapter 8 Optimization on page 78.
Onboard Advanced Technical
Diagnostics
PLC Parameters Data
NC


0.0300

UL
Information
PT PS
US
US
0.1
69