Emerson Quantum MP User Manual page 107

Safety Product Mechanical
Information Information Installation
Parameter
4.01 Current magnitude
4.02 Filtered current magnitude
4.03 Torque demand
4.04 Current demand
4.05 Motoring current limit
4.06 Regen current limit
4.07 Symmetrical current limit
4.08 Torque reference
4.09 Torque offset
4.10 Torque offset select
4.11 Torque mode selector
4.12 Current demand filter 1
4.13 Continuous current controller Kp gain
4.14 Continuous current controller Ki gain
4.15 Thermal time constant
4.16 Thermal protection mode
4.18 Overriding current limit
4.19 Overload accumulator
4.20 Percentage load
4.22 Inertia compensation enable
4.23 Current demand filter 2
4.24 User current maximum scaling
4.27 Current taper 1 threshold
4.28 Current taper 2 threshold
4.29 Current taper 1 end point
4.30 Current taper 2 end point
4.31 Taper threshold 1 exceeded
4.32 Taper threshold 2 exceeded
4.33 Slew rate limit
4.34 Discontinuous current controller Ki gain
4.35 Extra safe bridge change
Reduced hysteresis for bridge change
4.36
over
RW Read / Write RO Read only
FI Filtered DE Destination
Quantum MP User Guide
Issue: A4
Electrical Getting Basic
Installation Started parameters
Range(
{di08, 0.43} 0 to DRIVE_CURRENT_MAX A
0 to DRIVE_CURRENT_MAX A
{di07, 0.42} ±TORQUE_PROD_CURRENT_MAX %
±TORQUE_PROD_CURRENT_MAX %
0 to MOTOR1_CURRENT_LIMIT_MAX %
0 to MOTOR1_CURRENT_LIMIT_MAX %
0 to MOTOR1_CURRENT_LIMIT_MAX %
±USER_CURRENT_MAX %
±USER_CURRENT_MAX %
OFF (0) or On (1)
0 to 4
0 to 25.0 ms
0 to 4,000
0 to 4,000
0 to 3000.0
0 to 1
0 to TORQUE_PROD_CURRENT_MAX %
0 to 100.0 %
±USER_CURRENT_MAX %
OFF (0) or On (1)
0.0 to 25.0 ms
0.0 to TORQUE_PROD_CURRENT_MAX %
0 to 10,000.0 rpm
0 to 10,000.0 rpm
0 to 1,000.0%
0 to 1,000.0%
OFF (0) or On (1)
OFF (0) or On (1)
0.0 to 60,000%s
0 to 4,000
OFF (0) or On (1)
OFF (0) or On (1)
Uni Unipolar Bi
NC Not copied RA
www.emersonct.com
Running the SMARTCARD
Optimization
Motor Operation

)
-1
Bi-polar Bit Bit parameter
Rating dependent PT Protected
Onboard Advanced Technical
Diagnostics
PLC Parameters Data

Default( )
RO Uni FI NC PT
RO Uni FI NC PT
RO
RO
150.0 RW Uni
150.0 RW Uni
150.0 RW Uni
0.0 RW Bi
0.0 RW Bi
OFF (0) RW Bit
0 RW Uni
0.0 RW Uni
100 RW Uni
50 RW Uni
89.0 RW Uni
0 RW Bit
RO Uni
RO Uni
RO
OFF (0) RW Bit
0.0 RW Uni
150.0 RW Uni
10,000.0 rpm RW Uni
10,000.0 rpm RW Uni
1,000.0% RW Uni
1,000.0% RW Uni
RO Bit
RO Bit
7,000 RW Uni
200 RW Uni
OFF (0) RW Bit
OFF (0) RW Bit
Txt Text string
US User save PS
UL
Information
Type
Bi FI NC PT
Bi FI NC PT
RA US
RA US
RA US
US
US
US
US
US
US
US
US
US
NC PT
NC PT
Bi FI NC PT
US
US
RA US
US
US
US
US
US
US
US
US
Power down save
107