Full Descriptions - Emerson Quantum MP User Manual

High performance dc drive size 1 and size 2 45a to 700a, 480v two or four quadrant operation
Table of Contents

Advertisement

Safety
Product
Mechanical
Information
Information
Installation
Parameter
Fb09 Drive encoder speed feedback {0.79, 3.27}
in01
Analog input 3 mode
in02
Analog input 1
in03
Analog input 2
in04
Analog input 3
in05
T24 digital I/O 1 state
in06
T25 digital I/O 2 state
in07
T26 digital I/O 3 state
in08
T27 digital input 4 state
in09
T28 digital input 5 state
in10
T29 digital input 6 state
* Modes 1 and 2 are not user saved, Modes 0, 3 and 4 are user saved.
** Only applicable to Modbus RTU mode.
Key:
Coding
{X.XX}
Copied Menu 0 or advanced parameter
RW
Read/write: can be written by the user
RO
Read only: can only be read by the user
Bit
1 bit parameter: 'On' or 'OFF' on the display
Bi
Bipolar parameter
Uni
Unipolar parameter
Txt
Text: the parameter uses text strings instead of numbers.
Filtered: some parameters which can have rapidly changing
FI
values are filtered when displayed on the drive keypad for
easy viewing.
Destination: This parameter selects the destination of an
DE
input or logic function.
Rating dependent: this parameter is likely to have different
values and ranges with drives of different voltage and
current ratings. Parameters with this attribute will not be
transferred to the destination drive by SMARTCARDs when
RA
the rating of the destination drive is different from the
source drive and the file is a parameter file. However, the
value will be transferred if only the current rating is different
and the file is a differences from default type file.
Not copied: not transferred to or from SMARTCARDs
NC
during copying.
PT
Protected: cannot be used as a destination.
User save: parameter saved in drive EEPROM when the
US
user initiates a parameter save.
Power-down save: parameter automatically saved in drive
EEPROM when the under volts (UV) trip occurs. Power-
PS
down save parameters are also saved in the drive when the
user initiates a parameter save.
6.1

Full descriptions

6.1.1
Parameter x.00
SE00 {x.00}
Parameter zero
RW
Uni
0 to 32,767
Caution should be taken before writing to SMARTCARD data block 200
or before performing 9999 Erase SMARTCARD. Proceeding will
overwrite or erase the Quantum MP default parameter values stored in
SMARTCARD data block 200.
Quantum MP User Guide
Issue: A4
Electrical
Getting
Basic
Installation
Started
parameters
Range(
±10,000.0 rpm
0-20 (0), 20-0 (1), 4-20.tr (2), 20-4.tr (3), 4-20
{0.81, 7.15}
(4), 20-4 (5), VOLt (6), th.SC (7), th (8), th.
{0.82, 7.01}
±100.00%
{0.83, 7.02}
±100.0%
{0.84, 7.03}
±100.0%
{0.85, 8.01}
{0.86, 8.02}
{0.87, 8.03}
OFF (0) or On (1)
{0.88, 8.04}
{0.89, 8.05}
{0.90, 8.06}
Attribute
0
www.emersonct.com
Running the
SMARTCARD
Optimization
Motor
Operation
)
diSp (9)
Pr x.00 is available in all menus and has the following functions.
Value
String
0
No Act
1
SAUE
2
rEAd 1*
3
PrOg 1*
4
rEAd 2*
5
PrOg 2*
6
rEAd 3*
7
PrOg 3*
8
diS.diFF
9
diS.dESt Display destination parameters only
10
Eur
11
USA
12
rES OP
1000
1000
1070
1070
1233
1233
1244
1244
1255
1255
1256
1256
2001
2001*
3yyy
3yyy*
4yyy
4yyy*
5yyy
5yyy*
6yyy
6yyy*
6200
6200*
7yyy
7yyy*
8yyy
8yyy*
9555
9555*
9666
9666*
9777
9777*
9888
9888*
9999
9999*
12000**
12000**
12001**
12001**
* See Chapter 9 SMARTCARD Operation on page 81 for more
information of these functions.
** These functions do not require a drive reset to become active. All
other functions require a drive reset to initiate the function.
Onboard
Advanced
Technical
Diagnostics
PLC
Parameters
Data
Default(
)
RW
Bi
th(8)
RW Txt
RO
Bi
RO
Bi
RO
Bi
RO Bit
RO Bit
RO Bit
RO Bit
RO Bit
RO Bit
Action
No action
Save parameters
Transfer SMART card data block 1 to the drive
Transfer drive parameters as difference from
default to SMART card block number 1
Transfer SMART card data block 2 to the drive
Transfer drive parameters as difference from
default to SMART card block number 2
Transfer SMART card data block 3 to the drive
Transfer drive parameters as difference from
default to SMART card block number 3
Display non-default values only
Load European defaults
Load USA defaults
Reset all Solution Modules
Save parameters
Reset all Solution Modules
Load European defaults
Load USA defaults
Load European defaults (excluding menus 15 to 20)
Load USA defaults (excluding menus 15 to 20)
Transfer drive parameter to a card and create a
bootable difference from default SMART card block
with data block number 1 and clear parameter
11.42. If data block 1 exists it is over written.
Transfer drive parameters to SMART card block
number yyy
Transfer drive parameters as difference from
default to SMART card block number yyy
Transfer Onboard Applications Lite ladder
program to SMART card block number yyy
Transfer SMART card data block yyy to the drive
Transfer Quantum MP defaults from
SMARTCARD data block 200 to the drive
Erase SMART card data block yyy
Compare drive data with SMART card block yyy
Clear SMART card warning suppression flag
Set SMART card warning suppression flag
Clear SMART card read-only flag
Set SMART card read-only flag
Erase SMART card
Display non-default values only
Display destination parameters only
UL
Information
Type
FI NC PT US
US
NC PT
NC PT
NC PT
NC PT
NC PT
NC PT
NC PT
NC PT
NC PT
65

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents