Smartcard Trips - Emerson Quantum MP User Manual

Safety Product Mechanical
Information Information Installation
9.6

SMARTCARD trips

After an attempt to read, write or erase data to or from a SMARTCARD a trip may occur if there has been a problem with the command. Table 9-6 lists
the trip indications and conditions that will cause the SMARTCARD to trip,
Table 9-6 Trip conditions
Trip
SMARTCARD trip: The menu 0 parameter modification cannot be saved to the SMARTCARD because the necessary
C.boot
file has not been created on the SMARTCARD
A write to a Menu 0 parameter has been initiated with the keypad by exiting edit mode and Pr 11.42 (SE09, 0.30) is set for
177 auto or boot mode. However the necessary boot file has not been created on the SMARTCARD to take the new parameter
value. This occurs when Pr 11.42 (SE09, 0.30) is changed to auto or boot mode, but the drive is not subsequently reset.
SMARTCARD trip: SMARTCARD can not perform the required function as it is being accessed by a Solutions
C.BUSy
Module
An attempt has been made to access a SMARTCARD. However an Solutions Module is already accessing the
178
SMARTCARD.
C.Chg SMARTCARD trip: Data location already contains data
179 An attempt has been made to store data in a SMARTCARD data block that already exists.
C.Optn SMARTCARD trip: Solutions Modules installed are different between source drive and destination drive
Parameter data or default difference data is being transferred from a SMARTCARD to the drive, but the Solutions Module
categories are different between source and destination drives. This trip does not stop the data transfer, but is a warning that
180
the data for the Solutions Modules that are different will be set to the default values and not the values from the card. This trip
also applies if a compare is attempted between the data block and the drive.
C.Rdo SMARTCARD trip: SMARTCARD has the Read Only bit set
An attempt has been made to modify a read-only SMARTCARD (i.e. erase the card, erase a file or create a file). A
181 SMARTCARD is read-only if the read-only flag has been set or the card contains data blocks with numbers from 500 to 999.
Attempting to create data blocks with numbers from 500 to 999 will always cause a trip.
C.Err SMARTCARD trip: SMARTCARD data is corrupted
An attempt has been made to transfer a data block from a SMARTCARD to the drive or to compare a SMARTCARD data
182
block and the checksum is incorrect or the data structure on the card is incorrect.
C.dat SMARTCARD trip: Data location specified does not contain any data
An attempt has been made to transfer a data block from a SMARTCARD to the drive or to compare a SMARTCARD data
183
block and the block does not exist.
C.FULL SMARTCARD trip: SMARTCARD full
184 An attempt has been made to create a data block on a SMARTCARD, but there is not enough space on the card.
C.Acc SMARTCARD trip: SMARTCARD Read / Write fail
An attempt has been made to access a SMARTCARD, but a card is not present or communications failure has occurred
185 between the drive and the card. This trip is also produced if an attempt is made to access a data block that has already been
opened by an Solutions Module.
C.rtg SMARTCARD trip: The voltage and/or current rating of the source and destination drives are different
Parameter data or default difference data is being transferred from a SMARTCARD to the drive, but the current and /or
voltage ratings are different between source and destination drives. This trip does not stop the data transfer, but is a warning
186
that the data for the Solutions Modules that are different will be set to the default values and not the values from the card. This
trip also applies if a compare is attempted between the data block and the drive.
C.Typ SMARTCARD trip: SMARTCARD parameter set not compatible with drive
This trip is produced during a compare if the drive mode in the data block is different from the current drive mode and the file
is a parameter or defaults differences file. This trip is also produced if an attempt is made to transfer parameters from a
187
parameter or default difference to the drive if the drive mode in the data block is outside the allowed range of drive modes for
the drive.
C.cpr SMARTCARD trip: The values stored in the drive and the values in the data block on the SMARTCARD are different
A compare has been carried out between a data block on a SMARTCARD and the drive and the compare has failed. This trip
188
only occurs if the compare has not already failed with the following trips: C.Typ, C.rtg, C.Optn, C.BUSy, C.Acc or C.Err.
Quantum MP User Guide
Issue: A4
Electrical Getting Basic Running the
Installation Started parameters
www.emersonct.com
SMARTCARD
Optimization
Motor Operation
Condition
Onboard Advanced Technical
Diagnostics
PLC Parameters Data
UL
Information
85