Allen-Bradley PowerFlex 755T Installation Instructions Manual page 155

Table 31 - TB1 Terminal Designations
Terminal Name
Sh Shield
Sh
Ptc– Motor PTC (–)
Ptc+ Motor PTC (+)
Ao0– Analog Out 0 (–)
Sh
Ao0+ Analog Out 0 (+)
Sh
PTC–
PTC+
Ao1– Analog Out 1 (–)
Ao0–
Ao0+
Ao1–
Ao1+ Analog Out 1 (+)
Ao1+
–10V
10VC
–10V –10 Volt Reference 2k ohm minimum.
+10V
Ai0–
Ai0+
Ai1– 10VC 10 Volt Common
Ai1+
24VC
+24V
+10V +10 Volt Reference 2k ohm minimum.
DiC
Di0
Di1
Ai0– Analog Input 0 (–)
Di2
Di3
Di4
Ai0+ Analog Input 0 (+)
Di5
Ai1– Analog Input 1 (–)
Ai1+ Analog Input 1 (+)
24VC 24 Volt Common
+24V +24 Volt DC
Di C Digital Input
Common
Di 0 Digital Input 0
Di 1 Digital Input 1
Di 2 Digital Input 2
Di 3 Digital Input 3
Di 4 Digital Input 4
Di 5 Digital Input 5
(1) Digital Inputs are either 24 Volts DC (2262C) or 120 Volts AC (2262D) based on module catalog number. Ensure applied voltage is
correct for I/O module.
(2) See HW Input PTC on page 158 for PTC data.
(3) Differential Isolation - External source must be maintained at less than 160V with respect to PE. Input provides high common
mode immunity.
(4) For CE compliance use shielded cable. Cable length should not exceed 30 m (98 ft).
(5) I/O Module parameters will also have a Port designation.
ATTENTION: Risk of equipment damage exists. Ensure that the correct
voltage is applied to the I/O Module digital inputs. Refer to the I/O Module
catalog number to determine the voltage rating.
• 20-750-2262C-2R is rated 24 Volts DC
• 20-750-2263C-1R2T is rated 24 Volts DC
• 20-750-2262D-2R is rated 120 Volts AC
Rockwell Automation Publication 750-IN100B-EN-P - July 2017
Description
Terminating point for wire shields when an EMC
plate or conduit box is not installed.
Motor protection device (Positive Temperature
(2)
Coefficient).
Bipolar, ±10V, 11 bit & sign, 2 k ohm minimum
load.
4-20 mA, 11 bit & sign, 400 ohm maximum load.
For (–) and (+) 10 Volt references.
(3)
Isolated , bipolar, differential, 11 bit & sign.
Voltage Mode: ±10V @ 88k ohm input impedance.
Current Mode: 0-20 mA @ 93 ohm input
impedance.
Drive supplied logic input power.
200 mA max. per I/O module
600 mA max per drive
Common for Digital Inputs 0...5
(1)
24V DC (30V DC Max.) - Opto isolated
High State: 20...24V DC 11.2 mA DC
(1)
Low State: 0...5V DC
(1)
120V AC (132V AC Max.) 50/60 Hz
(1)
isolated
High State: 100...132V AC
(1)
Low State: 0...30V AC
(1)
I/O Wiring Chapter 6
Related
(5)
Param
40
on Port nn
75
on Port nn
85
on Port nn
50, 70
on Port nn
60, 70
on Port nn
1
on Port nn
(4)
- Opto
155