Commands (Before The Ieee488.2-1987 Standard) - YOKOGAWA WT110 User Manual

11.7 Commands (before the IEEE 488.2-1987 Standard)
11-12
For a detailed description of each command, refer to appendix 1.1.
Command
Wiring system WRm (WiRing)
Voltage range RVm (Range Voltage)
AVm(Auto Voltage range)
Current range RAm(Range current(A))
AAm(Auto current(A) range)
SAm(Sensor Ampere)
Display range DR(Display Range)
Measurement mode MNm(MeaN)
Filter FLm(FiLter)
Hold HDm(sampling HolD)
Trigger E or ST or <GET>
Display DAm(Display A function)
DBm(Display B function)
DCm(Display C function)
EAm(Element display A)
EBm(Element display B)
ECm(Element display C)
Scaling SCm(SCaling)
KVm(K*Amplre)
KAm(K*Wattage)
KWm(K*Voltage)
Averaging AGm(AveraGing)
ATm(Averaging Type)
ACm(Averaging Coefficient)
MATH MTm(MaThematics)
Integration IS(Integrate Start )
IP(Integrate stoP)
IR(Integrate Reset)
ICm(Integrate Continuous)
TMm1,m2(integrate TiMer)
Data storage SO(Store On)
SRm1,m2,m3(Store inteRval)
Data recalling ROm(Recall On)
RRm1,m2,m3(recall inteRval)
Set-up parameters SLm(panel Setting Load)
SSm(panel Setting Save)
RC(Reset Command)
Communication CMm(Communication coMmand)
commands OD(Output Data)
OFm1,m2,m3(Output Function)
OFDm(Output Function Default)
OS(Output panal Setting)
OE(Output Error code)
Hm(Header)
DLm(DeLimiter)
IMm(Interrupt Mask)
/HAM (option) HAm(Harmonics Analize)
HEm(Harmonics Eiement)
OR(harmonics ORder)
OHm1,m2(Output Harmonics function) sets communication or output block
PSm(Pll Source )
DFm(Distortion Formula)
/DA (option) OAm1,m2,m3(Output Analog)
OADm(Output Analog Default)
RTm1,m2,(integrate Rated Time)
/CMP (option) YOm(relaY On)
YMm(relaY Mode)
DYm(Display relaY)
YCm(relaY Channel)
OYm1,m2,m3,m4,m5
(Output relaY function)
OYHm1,m2,m3,m4,m5,m6
(Output relaY Harmonic function)
Note
• If commands relating to options are used on instruments which do not have the options installed, "Error
11" is displayed. Also, there are no responses to inquiries.
• "MATH" is available on WT110/WT130 with ROM version 2.01 or later.
Description
sets wiring system
sets voltage range
sets voltage auto range
sets current range
sets current auto range
sets external sensor
sets external sensor
sets external sensor
sets filter ON/OFF
holds display and output data
trigger
selects function to be displayed on display A
selects function to be displayed on display B
selects function to be displayed on display C
selects element to be displayed on display A
selects element to be displayed on display B
selects element to be displayed on display C
sets scaling ON/OFF
sets the scaling value
sets averaging ON/OFF
selects exponential averaging or moving averaging
sets attenuation constant or averaging number
Sets computing equation
starts integration
stops integration
resets integration
sets integration mode
sets integration preset time
starts storage
sets storage interval
starts recalling
sets recalling interval
recalling set-up parameters
storing set-up parameters
initialize set-up parameters
sets command group to be used
requests output of measured data
sets output items
sets default output items
requests output of setting parameters
requests output of error code
sets output data header
sets output data delimiter
sets status byte interrupt mask
sets harmonic analysis ON/OFF
sets harmonics element
sets harmonics order
sets PLL source
sets distortion formula
sets output items yourself
sets default output items
sets integration time
sets comparator function ON/OFF
sets comparator mode
sets display relay ON/OFF for comparator
sets the relay channel
sets the output relay function for normal measurement
sets the output relay function for harmonic analysis
IM 253401-01E