1. Manuals
  2. Brands
  3. ADC Manuals
  4. Modem
  5. MM702G2-W V5.x
  6. User manual

ADC MM702G2-W V5.x User Manual

Megabit modem
Hide thumbs Also See for MM702G2-W V5.x:
Table of Contents

Advertisement

Quick Links

Download this manual
®
Megabit Modem
MM702G2-W V5.x
User Manual
Product Catalog: MM702G2-W
Document Number: MM702G2-W-UM-03

Advertisement

Table of Contents
loading

Related Manuals for ADC MM702G2-W V5.x

Summary of Contents for ADC MM702G2-W V5.x

  • Page 1 ® Megabit Modem MM702G2-W V5.x User Manual Product Catalog: MM702G2-W Document Number: MM702G2-W-UM-03...
  • Page 2 Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice. In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits, and ADC further disclaims any and all liability for indirect, incidental, special, consequential or other similar damages.

  • Page 3: Table Of Contents

    Table of Contents Chapter 1: Installation ....................1-1 Overview ..........................1-1 Unpack the Modem ........................1-1 Determine What You Need ....................... 1-2 Connect Cables ........................1-3 Connect the 10/100Base-T Port ..................1-3 LED Status Indications ......................1-5 Chapter 2: Accessing the Web Interface for Modem Management ......2-1 Assign IP Addresses ........................
  • Page 4 Table of Contents Delete a WAN Session ......................5-26 Edit a WAN Session ....................... 5-26 Edit Service ........................5-27 Edit RFC1483 ........................5-29 Edit ATM Channel ......................5-31 Edit Bridge Interface ......................5-34 Edit Spanning Bridge Interface ..................5-37 Configure a SHDSL Port Configuration ................. 5-39 Before You Begin ........................
  • Page 5 Table of Contents Ports ............................6-58 Ethernet ..........................6-58 Ports ............................6-59 SHDSL ..........................6-59 Chapter 7: Maintenance ....................7-1 Telnet Access ........................... 7-1 Management IP ........................7-2 Firmware Update ........................7-3 Backup/Restore ........................7-4 Restart/Set Factory Default ...................... 7-5 Reset to Factory Defaults using the Reset Button .............
  • Page 6 Table of Contents Page Intentionally Left Blank MM702G2-W-UM-03...
  • Page 7 List of Figures Figure 1-1. Remove the Modem ..................1-1 Figure 1-2. Set the MDI/MDI-X Switch ................1-3 Figure 1-3. Rear Panel Connections .................. 1-4 Figure 2-1. TCP/IP Properties ..................... 2-1 Figure 2-2. Internet Options ....................2-2 Figure 2-3. LAN Settings ..................... 2-3 Figure 2-4.
  • Page 8 List of Figures Figure 5-5. Edit IP Interface ....................5-5 Figure 5-6. Advanced ......................5-7 Figure 5-7. Edit Tcp Mss Clamp ..................5-7 Figure 5-8. Advanced ......................5-9 Figure 5-9. Edit RIP Versions ....................5-9 Figure 5-10.Advanced ....................... 5-11 Figure 5-11.Edit NAT ......................5-12 Figure 5-12.WAN Configuration ..................
  • Page 9 List of Figures Figure 6-9. Add TCP or UDP Filter ................... 6-10 Figure 6-10.Add TCP or UDP Port Filter ................6-11 Figure 6-11.Add Raw IP Filter .................... 6-12 Figure 6-12.Select Add Host Validator ................6-13 Figure 6-13.Add Host Validator ..................6-14 Figure 6-14.Security Trigger Configuration ................
  • Page 10 List of Figures Figure 6-46.Create New Subnet ..................6-48 Figure 6-47.Create New Fixed Host .................. 6-49 Figure 6-48.DHCP Relay ....................6-50 Figure 6-49.DNS Client Servers ..................6-51 Figure 6-50.DNS Relay ...................... 6-52 Figure 6-51.DNS Relay Local LAN Database ..............6-53 Figure 6-52.Create/View DNS Relay Local LAN ...............
  • Page 11 List of Tables Table 1-1. Required Equipment ................... 1-2 Table 1-2. LED Status Indicators ..................1-5 Table 4-1. User Access Levels ..................... 4-4 Table A-1.SHDSL Port (RJ-11) (2-Wire) ................A-15 Table A-2.SHDSL Port (RJ-11) (4-Wire) ................A-15 Table A-3.10/100Base-T Port (RJ-45) ................A-16 Table A-4.Console Port (RJ-45) ..................A-16 MM702G2-W-UM-03...
  • Page 12 List of Tables Page Intentionally Left Blank MM702G2-W-UM-03...
  • Page 13 Chapter 3: View Status Parameters. NTENDED UDIENCE This manual is intended for anyone who installs, configures, and manages the ADC Megabit Modem MM702G2-W. ONVENTIONS The following style conventions and terminology are used throughout this guide. Element Meaning Bold font Text that you must input exactly as shown (e.g., type 1 for card 1), menu buttons...
  • Page 14 • Unpack each container and visually inspect the contents for signs of damage. If the equipment has been dam- aged in transit, immediately report the extent of damage to the transportation company and to ADC. Order replacement equipment, if necessary.

  • Page 15: Chapter 1: Installation

    Chapter NSTALLATION VERVIEW The MM702G2-W is a versatile, 1-pair/2-pair high-speed modem that connects an Ethernet LAN to one or more service providers using G.shdsl transmission technology in fixed and rate adaptive modes with date rates up to 4.608 Mbps. The connections provide instant and high-speed broadband access to the Internet or to other types of Wide Area Networks (WANs).

  • Page 16: Determine What You Need

    Chapter 1: Installation ETERMINE In addition to what is shipped with the modem, you need the following hardware and software to complete the installation and configuration. Table 1-1. Required Equipment Equipment Requirement Hardware Ethernet NIC Card (10/100 Mbps) installed in each PC and other network equipment that will be connected to the LAN.

  • Page 17: Connect Cables

    Chapter 1: Installation ONNECT ABLES Install cables for the Ethernet port (see “Connect the 10/100Base-T Port” below). Then check “LED Status Indications” on page 1-5. Connect the 10/100Base-T Port Set the modem MDI/MDI-X switch for the 10/100Base-T port to allow the modem to connect directly to other network devices such as a PC, hub, switch, or router.

  • Page 18: Figure 1-3. Rear Panel Connections

    Chapter 1: Installation Step Action Connect the cables to the modem rear panel as shown below in Figure 1-3: • Silver cable to the SHDSL line port and wall jack • Black Ethernet cable to the 10/100Base-T port and to another Ethernet device such as a PC, hub, switch or router •...

  • Page 19: Led Status Indications

    Chapter 1: Installation LED S TATUS NDICATIONS Table 1-2 summarizes the modem’s operational status as provided by the front panel LEDs. Table 1-2. LED Status Indicators State Description On green Modem has power. Modem does not have power. LINK On green A PC, hub, switch or other network device is connected to the modem 10/100Base-T interface.
  • Page 20 Chapter 1: Installation Page Intentionally Left Blank MM702G2-W-UM-03...

  • Page 21: Assign Ip Addresses

    Chapter CCESSING THE NTERFACE FOR ODEM ANAGEMENT Use the Web interface to set up and manage the modem. This chapter provides steps to help you access the Web interface pages for configuration and management of the modem. IP A SSIGN DDRESSES To access the modem Web interface, the management PC must be on the same LAN Modem Defaults...

  • Page 22: Set Up The Web Browser

    Chapter 2: Accessing the Web Interface for Modem Management Step Action Enter an IP Address and Subnet Mask that places the management PC on the same subnet as the modem. Use an IP address in the range of 192.168.0.2 to 192.168.0.254. Click OK to close the TCP/IP Properties dialog.

  • Page 23: Figure 2-3. Lan Settings

    Chapter 2: Accessing the Web Interface for Modem Management Step Action Click the Connections tab, then click LAN Settings to open the LAN Settings dialog (Figure 2-3). Figure 2-3. LAN Settings In the Proxy Server section of the dialog, do one of the following: •...

  • Page 24: Accessing The Modem Web

    Chapter 2: Accessing the Web Interface for Modem Management CCESSING THE ODEM AGES Use the following steps to access the login page, enter the Web interface, and navigate the Web pages. This login is for the system administrator responsible for configuring and managing the modem. Step Action Do one of the following to access the modem Web pages:...

  • Page 25: Figure 2-5. Enter User Name And Password

    Chapter 2: Accessing the Web Interface for Modem Management Step Action Enter the User Name and Password, then click OK. Login Defaults Username: admin Password: password Figure 2-5. Enter User Name and Password The Operational Status page is displayed and functions as a home page with a menu bar. This menu bar provides navigation to all Web pages used for configuration and management.

  • Page 26: Menu Structure

    Chapter 2: Accessing the Web Interface for Modem Management TRUCTURE Figure 2-7, Figure 2-8, and Figure 2-9 show the menu structure of the terminal management system. MM702G2-W MM702G2-W Status Configuration Operational Status LAN Connection System Information LAN Protocol Set Time (See SNTP Client) Routed Bridged Statistics...
  • Page 27 Chapter 2: Accessing the Web Interface for Modem Management MM702G2-W MM702G2-W Configuration Configuration Create New Service Edit RFC 1483 Bridged Edit Service Description Session Name Edit RFC 1483 Encapsulation Encapsulation RFC 1483 Routed Edit ATM Channel Session Name Encapsulation ATM QOS Use DHCP Burst Tolerance WAN IP Address...
  • Page 28 Chapter 2: Accessing the Web Interface for Modem Management MM702G2-W MM702G2-W Configuration Configuration Advance Advance Default Gateway Security Security State IP Address Proxy ARP Policies, Triggers, Intrusion Detection, Logging Create New Proxy ARP Entry Security Policy Configuration IP Address Port Filter Mask Exclude Add TCP or UDP Filter...
  • Page 29 Chapter 2: Accessing the Web Interface for Modem Management MM702G2-W MM702G2-W Configuration Configuration Advance Advance Security ZIPB LAN Interface Security State WAN Interface LAN IP Address Spoof Method Policies, Triggers, Intrusion Detection, Logging Manual LAN IP Address LAN Subnet Mask Selection Method Configure Intrusion Detection Manual LAN Subnet Mask LAN DHCP Server Lease Time...
  • Page 30 Chapter 2: Accessing the Web Interface for Modem Management MM702G2-W MM702G2-W Configuration Configuration Advance Advance Bridge Bridge Global Setting Global Setting Bridge MAC Address Interface Configuration Numbers of Ports Bridge Type Bridge Interface Unicast Learning Multicast Learning Filter Type Config PVID Status Add Port to Filter Mask Tagging PVID...
  • Page 31 Chapter 2: Accessing the Web Interface for Modem Management MM702G2-W MM702G2-W Configuration Configuration Advance Advance Bridge DHCP Spanning Tree DHCP Server Spanning DHCP Server Interface Priority Forward Delay Create New Subnet Hello Time Maximum Age Subnet Value Subnet Mast Unicast Destination Get Subnet from IP Interface MAC Filtering Maximum Lease Time...
  • Page 32 Chapter 2: Accessing the Web Interface for Modem Management MM702G2-W MM702G2-W Configuration Configuration Advance Advance Ports DNS Client Ethernet DNS Servers Auto Negotiation Domain Search Order Speed Mode DNS Relay SHDSL DNS Relay LAN Database Basic Port Attributes Local Domain Name Mode Create/View LAN Database Annex Type...

  • Page 33: Chapter 3: View Status Parameters

    Chapter TATUS ARAMETERS Status provides an overall management view of the modem configuration and performance. The system information page, which also functions as the Web interface home page, provides a management view of modem configuration. The information covered is: Operational Status, System Information, Routing Table, ARP Table, Bridge Interfaces, VLAN Port Statistics, Ethernet Statistics, ATM Statistics and SHDSL Statistics.
  • Page 34 Chapter 3: View Status Parameters Step Action View the Status as described below: • Local IP Address – Identifies the Local IP Address. • Port Connection Status – Includes status on type, whether connected and line state of the Ethernet and SHDSL ports.

  • Page 35: View System Information

    Chapter 3: View Status Parameters YSTEM NFORMATION Step Action Select Status|System Information to access the System Information page (Figure 3-2). Figure 3-2. System Information View the System Information as described below: • Up-Time – Identifies the time the modem has been up and running. •...

  • Page 36: Statistics

    Chapter 3: View Status Parameters Statistics View Routing Table Step Action Select Status|Statistics|Routing Table to access the Routing Table page (Figure 3-3). Figure 3-3. Routing Table View the Routing Table for the following information: • Destination The IP address for the destination network, subnet, or host to which the packets are directed. Use 0.0.0.0 as the destination IP address for a default route.

  • Page 37: Figure 3-4. Arp Table

    Chapter 3: View Status Parameters View ARP Table Step Action Select Status|Statistics|ARP Table to access the Address Resolution Protocol (ARP) Table page (Figure 3-4). Figure 3-4. ARP Table View the ARP Table for the following information: • IP Address The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. •...

  • Page 38: Figure 3-5. Bridge Interfaces

    Chapter 3: View Status Parameters View Bridge Interfaces Step Action Select Status|Statistics|Bridge Interfaces to access the Bridge Interfaces page (Figure 3-5). Figure 3-5. Bridge Interfaces MM702G2-W-UM-03...
  • Page 39 Chapter 3: View Status Parameters Step Action NOTE: With each interface, there are two links provided (Clear and Flush) for Clearing statistics and Flushing the dynamic entries for the interface respectively. View the Bridge Interfaces for the following information: • Name The name of the interface.

  • Page 40: Figure 3-6. Vlan Port Statistics

    Chapter 3: View Status Parameters View VLAN Port Statistics Step Action Select Status|Statistics|VLAN Port Statistics to access the VLAN Port Statistics page (Figure 3-6). Figure 3-6. VLAN Port Statistics View the VLAN Port Table for the following information: • Interface The name of the interface.

  • Page 41: Figure 3-7. Ethernet Statistics

    Chapter 3: View Status Parameters View Ethernet Statistics Step Action Select Status|Statistics|Ethernet Statistics to access the Ethernet Statistics page (Figure 3-7). Figure 3-7. Ethernet Statistics MM702G2-W-UM-03...
  • Page 42 Chapter 3: View Status Parameters Step Action View the Ethernet Statistics as described below: • Port Name – Name assigned to this Port (Ethernet). • Connected – Values are True and False. • Rx Packets – The total number of packets received for Ethernet port. •...

  • Page 43: Figure 3-8. Atm Statistics

    Chapter 3: View Status Parameters View ATM Statistics Step Action Select Status|Statistics|ATM Statistics to access the ATM Statistics page (Figure 3-8). Figure 3-8. ATM Statistics MM702G2-W-UM-03 3-11...
  • Page 44 Chapter 3: View Status Parameters Step Action View the ATM Statistics for the following information: • Port Name – Name assigned to this Port (SHDSL). • Rx VPI – Received VPIs. Values range from 0-4095. • Rx VCI – Received VCIs. Values range from 32-65535. •...

  • Page 45: Figure 3-9. Shdsl Statistics

    Chapter 3: View Status Parameters View SHDSL Statistics Step Action Select Status|Statistics|SHDSL Statistics|SHDSL to access the SHDSL page (Figure 3-9). Figure 3-9. SHDSL Statistics View the current SHDSL Line status for the following information: • Bit Rate – Number of bits that are conveyed or processed per unit of time, meaured in bits per second.

  • Page 46: Figure 3-10.Shdsl Errors

    Chapter 3: View Status Parameters View SHDSL Errors Step Action Select Status|Statistics|SHDSL Statistics|Errors to access the SHDSL Errors page (Figure 3-10). Figure 3-10. SHDSL Errors 3-14 MM702G2-W-UM-03...
  • Page 47 Chapter 3: View Status Parameters Step Action View the SHDSL page for the following information: • SHDSL Errors – Error LOSW Indicates the total number of loss of sync word (LOSW) defects that have occurred since the last time that the G.shdsl error counters were cleared. An LOSW is indicated when three or more consecutive frames contain one or more bit errors in the frame sync word.
  • Page 48 Chapter 3: View Status Parameters Page Intentionally Left Blank 3-16 MM702G2-W-UM-03...

  • Page 49: Chapter 4: View And Configure System Parameters

    Chapter IEW AND ONFIGURE YSTEM ARAMETERS The information covered is: Save Configuration, Configure User Administration parameters, Retrieve Event Log information, and Configure SNTP parameters. ONFIGURATION HANGES Use the Save Changes page for saving your current configuration to flash memory. This option immediately writes all current system configuration to permanent memory (NVRAM).

  • Page 50: Figure 4-2. Configuration Save Complete

    Chapter 4: View and Configure System Parameters Step Action Do one of the following: a. To confirm that you want to save the changes, click Save (Figure 4-1 on page 4-1). Confirming save will write the configuration to flash memory. Do not power off the modem while the save is in progress.

  • Page 51: Configure User Administration

    Chapter 4: View and Configure System Parameters ONFIGURE DMINISTRATION Assigning and Editing User Access The modem provides secure access for managing and viewing modem configuration. Three levels of access are predefined and can be assigned to users you set up. These security logons are required for access to the Web interface.

  • Page 52: Figure 4-4. Add New User

    Chapter 4: View and Configure System Parameters Step Action To add a new user account, do the following: a. Click Create a new user (Figure 4-3 on page 4-3). Figure 4-4 is displayed. Figure 4-4. Add New User Note: It is important to change the password for all three default user accounts to ensure secure access to the modem for configuration and management.

  • Page 53: Figure 4-5. Edit User - Admin

    Chapter 4: View and Configure System Parameters Step Action c. Click Create. The new entry is now viewable from the Users’ List table (Figure 4-3 on page 4-3). (cont.) To modify or delete an existing user entry, do the following: Note: It is important to change the default password for all three default user accounts to ensure secure access to modem for configuration and management.

  • Page 54: View Event Logs

    Chapter 4: View and Configure System Parameters VENT Step Action Select System|Event Log to access the Event Log page (Figure 4-6). Figure 4-6. All Event Logs Press the arrow beside Select a Log to view the following System Information: • All Events – Shows all System Events. •...

  • Page 55: Configure Sntp Client

    Chapter 4: View and Configure System Parameters SNTP C ONFIGURE LIENT Step Action Select System|SNTP Client to access the Simple Network Time Protocol (SNTP) Client page (Figure 4-7). Figure 4-7. SNTP Configure the SNTP parameters as described below: • Synchronize – To synchronize the client with the NTP Server, click Synchronize. •...
  • Page 56 Chapter 4: View and Configure System Parameters Page Intentionally Left Blank MM702G2-W-UM-03...

  • Page 57: Chapter 5: Configure Lan, Wan, And Shdsl

    Chapter LAN, WAN, SHDSL ONFIGURE LAN C ONNECTIONS The LAN configuration sets up the interface between the modem 10/100Base-T LAN port and devices on the LAN. The LAN is managed by your network administrator, who will make the decisions concerning its topology. For instructions on setting up the LAN interface for a point-to-point modem application, go to Configure the LAN below.

  • Page 58: Figure 5-2. Lan Port

    Chapter 5: Configure LAN, WAN, and SHDSL Step Action The default LAN IP interface is iplan. To change the IP address for the LAN Port, click on Change LAN Port IP Address from the LAN Connections page. Figure 5-2 is displayed. Figure 5-2.

  • Page 59: Figure 5-3. Create A Virtual Interface

    Chapter 5: Configure LAN, WAN, and SHDSL Step Action Configure the following parameters: Primary IP Address • IP Address See the LAN administrator for a LAN IP address. – Enter an IP address for the LAN (10/100Base-T) port provided by the LAN administrator. –...

  • Page 60: Edit Alan

    Chapter 5: Configure LAN, WAN, and SHDSL Step Action Configure the following parameters: • IP Address – Configure the IP address which is on a different subnet as the LAN IP address. • Netmask – The network mask for the Virtual IP address configured. Click Apply.

  • Page 61: Edit Lan Protocol

    Chapter 5: Configure LAN, WAN, and SHDSL Edit LAN Protocol Step Action Select Configuration|LAN Connections|Change LAN Port IP Address to access the LAN Port page (Figure 5-4). Figure 5-4. Advanced Click Advanced (Figure 5-4). Figure 5-5 is displayed. Figure 5-5. Edit IP Interface MM702G2-W-UM-03...
  • Page 62 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Edit the following parameters (as appropriate): • IP Address See the LAN administrator for a LAN IP address. Do one of the following, then click Apply: – Enter an IP address for the LAN (10/100Base-T) port provided by the LAN administrator. –...

  • Page 63: Edit Tcp Mss Clamp

    Chapter 5: Configure LAN, WAN, and SHDSL Edit TCP MSS Clamp Step Action Select Configuration|LAN Connections|Change LAN Port IP Address to access the LAN Port page (Figure 5-6). Figure 5-6. Advanced Click Advanced (Figure 5-6). Figure 5-7 is displayed. Figure 5-7. Edit Tcp Mss Clamp MM702G2-W-UM-03...
  • Page 64 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Edit the following parameter (as appropriate): • TCP MSS Clamp Valid values are True or False. Default is False. Problem When using the PPPoE Client for an Internet connection, the user's PC may not be able to browse some websites.

  • Page 65: Edit Rip Versions

    Chapter 5: Configure LAN, WAN, and SHDSL Edit RIP Versions Step Action Select Configuration|LAN Connections|Change LAN Port IP Address to access the LAN Port page (Figure 5-8). Figure 5-8. Advanced Click Advanced (Figure 5-8). Figure 5-9 is displayed. Figure 5-9. Edit RIP Versions MM702G2-W-UM-03...
  • Page 66 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Edit the following parameters (as appropriate): • Accept V1 Valid values are True or False. Default is False. • Accept V2 Valid values are True or False. Default is False. • Send V1 Valid values are True or False.

  • Page 67: Edit Nat

    Chapter 5: Configure LAN, WAN, and SHDSL Edit NAT NAT provides the ability to map private IP address on the LAN to public IP addresses (WAN) that are assigned to each session. This essentially hides the private IP addresses behind the public IP addresses assigned to WAN sessions.

  • Page 68: Figure 5-11.Edit Nat

    Chapter 5: Configure LAN, WAN, and SHDSL Step Action Click Advanced (Figure 5-10). Figure 5-11 is displayed. Figure 5-11. Edit NAT 5-12 MM702G2-W-UM-03...
  • Page 69 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Edit the following parameter (as appropriate): • NAT Enabled Valid values are True or False. Default is False. Click Change to change the parameters or click Reset to keep the current settings. MM702G2-W-UM-03 5-13...

  • Page 70: Configuring The Wan

    Chapter 5: Configure LAN, WAN, and SHDSL ONFIGURING THE The WAN configuration sets up from 1 to 8 sessions between the modem and the service provider or between two G.shdsl modems (refer to “Implementing a Point-To-Point LAN Extension” on page 8-1).

  • Page 71: Configure A New Wan Session

    Chapter 5: Configure LAN, WAN, and SHDSL WAN S ONFIGURE A ESSION You can configure up to 8 total PPPoA, PPPoE, 1483-Bridge, and 1483-Router sessions for the modem. From the WAN configuration page (Figure 5-12), define the parameters for each session. Step Action Select Configuration|WAN to access the WAN Configuration page...

  • Page 72: Set Up An Rfc 1483 Bridged Session

    Chapter 5: Configure LAN, WAN, and SHDSL Set Up an RFC 1483 Bridged Session Step Action Select Configuration|WAN|Create a new service to access the WAN Connection: Create Service page. Click on RFC 1483 Bridged (Figure 5-13). Figure 5-13. Select RFC 1483 Bridged Click Configure.
  • Page 73 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Configure the following parameters for each session: • Session Name Enter a unique, descriptive identifier for the session. This name can have a maximum of 32 characters. • Virtual Path ID (VPI) Enter the value (from 0 to 4,095) provided by the service provider.

  • Page 74: Set Up An Rfc 1483 Routed

    Chapter 5: Configure LAN, WAN, and SHDSL Set Up an RFC 1483 Routed Step Action Select Configuration|WAN|Create a new service to access the WAN Connection: Create Service page. Click on RFC 1483 Routed (Figure 5-15). Figure 5-15. Select RFC 1483 Routed Click Configure.
  • Page 75 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Configure the following parameters for each session: • Session Name Enter a unique, descriptive identifier for the session. This name can have a maximum of 32 characters. • Virtual Path ID (VPI) Enter the value (from 0 to 4,095) provided by the service provider.

  • Page 76: Set Up A Pppoa Routed

    Chapter 5: Configure LAN, WAN, and SHDSL Set Up a PPPoA Routed Step Action Select Configuration|WAN|Create a new service to access the WAN Connection: Create Service page. Click on PPPoA Routed (Figure 5-17). Figure 5-17. Select PPPoA Routed Click Configure. Figure 5-18 is displayed.
  • Page 77 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Configure the following parameters for each session: • Session Name Enter a unique, descriptive identifier for the session. This name can have a maximum of 32 characters. • Virtual Path ID (VPI) Enter the value (from 0 to 4,095) provided by the service provider.

  • Page 78: Set Up A Pppoe Routed

    Chapter 5: Configure LAN, WAN, and SHDSL Set Up a PPPoE Routed Step Action Select Configuration|WAN|Create a new service to access the WAN Connection: Create Service page. Click on PPPoE Routed (Figure 5-19). Figure 5-19. Select PPPoE Routed Click Configure. Figure 5-20 is displayed.
  • Page 79 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Configure the following parameters for each session: • Session Name Enter a unique, descriptive identifier for the session. This name can have a maximum of 32 characters. • Virtual Path ID (VPI) Enter the value (from 0 to 4,095) provided by the service provider.

  • Page 80: Set Up A Ipoa Routed

    Chapter 5: Configure LAN, WAN, and SHDSL Set Up a IPoA Routed Step Action Select Configuration|WAN|Create a new service to access the WAN Connection: Create Service page. Click on IPoA Routed (Figure 5-21). Figure 5-21. Select IPoA Routed Click Configure. Figure 5-22 is displayed.
  • Page 81 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Configure the following parameters for each session: • Session Name Enter a unique, descriptive identifier for the session. This name can have a maximum of 32 characters. • Virtual Path ID (VPI) Enter the value (from 0 to 4,095) provided by the service provider.

  • Page 82: Delete Awan Session

    Chapter 5: Configure LAN, WAN, and SHDSL Permanently Save Sessions After you have set up all the WAN sessions, save these changes permanently, as described in Save Configuration Changes on page 4-1. WAN S ELETE A ESSION To Delete a WAN Session, click Delete (Figure 5-12), then click Delete this connection once prompted.

  • Page 83: Edit Service

    Chapter 5: Configure LAN, WAN, and SHDSL Edit Service Step Action Select Configuration|WAN to access the WAN Configuration page (Figure 5-23). Figure 5-23. WAN Configuration MM702G2-W-UM-03 5-27...

  • Page 84: Figure 5-24.Edit Service

    Chapter 5: Configure LAN, WAN, and SHDSL Step Action Click Edit (Figure 5-23). Figure 5-24 is displayed. Figure 5-24. Edit Service Edit the following parameter (as appropriate): • Description Enter a unique, descriptive identifier as the Description. This name can have a maximum of 32 characters.

  • Page 85: Edit Rfc1483

    Chapter 5: Configure LAN, WAN, and SHDSL Edit RFC1483 Step Action Select Configuration|WAN to access the WAN Configuration page (Figure 5-25). Figure 5-25. WAN Configuration MM702G2-W-UM-03 5-29...

  • Page 86: Figure 5-26.Edit Rfc1483

    Chapter 5: Configure LAN, WAN, and SHDSL Step Action Click Edit (Figure 5-25). Figure 5-26 is displayed. Click Edit RFC1483. Figure 5-26. Edit RFC1483 Edit the following parameter (as appropriate): • LlcBridged Logical Link Control allows multiple protocols to be run over the session. This is the default encapsula- tion.

  • Page 87: Edit Atm Channel

    Chapter 5: Configure LAN, WAN, and SHDSL Edit ATM Channel Step Action Select Configuration|WAN to access the WAN Configuration page (Figure 5-27). Figure 5-27. WAN Configuration MM702G2-W-UM-03 5-31...

  • Page 88: Figure 5-28.Edit Atm Channel

    Chapter 5: Configure LAN, WAN, and SHDSL Step Action Click Edit (Figure 5-27). Figure 5-28 is displayed. Click Edit ATM Channel. Figure 5-28. Edit ATM Channel 5-32 MM702G2-W-UM-03...
  • Page 89 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Edit the following parameter (as appropriate): • VPI Enter the value (from 0 to 4,095) provided by the service provider. The number identifies the virtual path that transports ATM cells between the modem and the service provider. This value must match the virtual path identification (VPI) value the service provider uses for this connection.

  • Page 90: Edit Bridge Interface

    Chapter 5: Configure LAN, WAN, and SHDSL Edit Bridge Interface Step Action Select Configuration|WAN to access the WAN Configuration page (Figure 5-29). Figure 5-29. WAN Configuration 5-34 MM702G2-W-UM-03...

  • Page 91: Figure 5-30.Edit Bridge Interface

    Chapter 5: Configure LAN, WAN, and SHDSL Step Action Click Edit (Figure 5-29). Figure 5-30 is displayed. Click Edit Bridge Interface. Figure 5-30. Edit Bridge Interface MM702G2-W-UM-03 5-35...
  • Page 92 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Edit the following parameter (as appropriate): • Leave Mode Valid values are Normal and Fast. Default is Normal. • IGMP Port State Valid values are Disable, Enable and Drop. Default is Disable. •...

  • Page 93: Edit Spanning Bridge Interface

    Chapter 5: Configure LAN, WAN, and SHDSL Edit Spanning Bridge Interface Step Action Select Configuration|WAN to access the WAN Configuration page (Figure 5-31). Figure 5-31. WAN Configuration MM702G2-W-UM-03 5-37...

  • Page 94: Figure 5-32.Edit Spanning Bridge Interface

    Chapter 5: Configure LAN, WAN, and SHDSL Step Action Click Edit (Figure 5-31). Figure 5-32 is displayed. Click Edit Spanning Bridge Interface. Figure 5-32. Edit Spanning Bridge Interface Edit the following parameter (as appropriate): • Priority The modem STP priority (how centrally located this bridge is) in the network. A lower number indicates a more centrally located bridge.

  • Page 95: Configure Ashdsl Port Configuration

    Chapter 5: Configure LAN, WAN, and SHDSL SHDSL P ONFIGURE A ONFIGURATION The SHDSL parameters set up the G.shdsl communication between the modem and a DSLAM or between two modems used in a point-to-point application. Typically, the SHDSL parameters for the modem are preset to immediately synchronize with the service provider (DSLAM application).

  • Page 96: Figure 5-33.Shdsl Port Configuration

    Chapter 5: Configure LAN, WAN, and SHDSL Step Action Select Configuration|SHDSL to access the SHDSL Port Configuration page (Figure 5-33). Figure 5-33. SHDSL Port Configuration Configure the Admin State parameter (Figure 5-33 on page 5-40). Set to Disable to configure the G.SHDSL parameters.
  • Page 97 Chapter 5: Configure LAN, WAN, and SHDSL Step Action Configure the following parameters: • Mode The four mode options are: CPE-2Wire, CPE-GS4Wire, CO-2Wire, and CO-GS4Wire. For 2-wire, default is CPE-2Wire. For 4-wire, default is CPE-GS4Wire. When the modem is connected to a service provider through a DSLAM, the operating mode is CPE-2 wire (default setting).
  • Page 98 Chapter 5: Configure LAN, WAN, and SHDSL Step Action • PSD Mode (cont) The Power Spectral Density (PSD) plots the variations of signal power with signal frequency for the G.shdsl transmission between the modem and the DSLAM or the modem and another modem. Symmetric PSD indicates that the PSD mask for both sides of the transmission (the CO- and remote- side) are the same (symmetric).

  • Page 99: Chapter 6: Configuring Advanced Features

    Chapter ONFIGURING DVANCED EATURES These configuration parameters affect system functions for the modem. Other system parameters used to manage or troubleshoot the modem (updating modem software, for example) are at the end of this section. EFORE EGIN Determine the following before changing system parameters: •...

  • Page 100: Figure 6-1. Default Gateway

    Chapter 6: Configuring Advanced Features Step Action Select Configuration|Advance|Default Gateway on the menu bar to access the Default Gateway page (Figure 6-1). Figure 6-1. Default Gateway To add a default gateway, enter the IP address for the gateway through which the modem will forward packets.

  • Page 101: Add Proxy Arp

    Chapter 6: Configuring Advanced Features ROXY Step Action Select Configuration|Advance|Proxy ARP to access the Proxy ARP Configuration page (Figure 6-2). Figure 6-2. Proxy ARP Configuration MM702G2-W-UM-03...

  • Page 102: Figure 6-3. Create Proxy Arp Entry

    Chapter 6: Configuring Advanced Features Step Action Click Create New Proxy ARP Entry. Figure 6-3 is displayed. Figure 6-3. Create Proxy ARP Entry Configure the Proxy ARP parameters: • IP Address – The format of a IP address is a 32-bit numeric address written as four numbers sepa- rated by periods (e.g., 192.168.0.101).

  • Page 103: Add Snmp Communities

    Chapter 6: Configuring Advanced Features SNMP C OMMUNITIES An SNMP community provides the authentication and authorization, through its community string, to view and/or change modem parameters. To enable SNMP access to the modem, SNMP community strings need to be configured. Step Action Select Configuration|Advance|SNMP Community to access the SNMP Community List page...

  • Page 104: Figure 6-5. Add New Community

    Chapter 6: Configuring Advanced Features Step Action To add a new SNMP community, do the following: a. Click on Create a New Community (Figure 6-4 on page 6-5). Figure 6-5 is displayed. Figure 6-5. Add New Community b. Enter the following information for the SNMP community. –...

  • Page 105: Security

    Chapter 6: Configuring Advanced Features ECURITY Step Action Select Configuration|Advance|Security to access the Security Interface Configuration page (Figure 6-6). Figure 6-6. Security Interface Configuration To configure the Security State, click one of the following parameters for each session: • Security – Values are Disabled and Enabled. Default is Disabled. •...

  • Page 106: Figure 6-7. Security: Add Interface

    Chapter 6: Configuring Advanced Features Step Action To set the Security Level, you must Enable Firewall to set the level. Valid values are Block All, High, Medium, and Low. Default is Block All. Click Change Level. To set Security Interfaces, interfaces must be defined and security enabled to configure NAT. To add an interface, you must set the Security State to Enable for Security, Firewall and Intrusion Detection (Figure 6-6 on page...

  • Page 107: Policies, Triggers, Intrusion Detection, Logging

    Chapter 6: Configuring Advanced Features Policies, Triggers, Intrusion Detection, Logging Step Action From the Security Interface Configuration page (Figure 6-6 on page 6-7), click Security Policy Configuration under Policies, Triggers, Intrusion Detection, Logging. Figure 6-8 is displayed. Figure 6-8. Security Policy Configuration MM702G2-W-UM-03...

  • Page 108: Figure 6-9. Add Tcp Or Udp Filter

    Chapter 6: Configuring Advanced Features Policy Filter Step Action Click Port Filters (Figure 6-8 on page 6-9). Figure 6-9 is displayed. Figure 6-9. Add TCP or UDP Filter 6-10 MM702G2-W-UM-03...

  • Page 109: Figure 6-10.Add Tcp Or Udp Port Filter

    Chapter 6: Configuring Advanced Features Step Action Click Add TCP or UPD Filter (Figure 6-9 on page 6-10). Figure 6-10 is displayed. Figure 6-10. Add TCP or UDP Port Filter Configure the following parameters for each session: • Source Address – Values are IP Address and Mask. Default is 0.0.0.0. •...

  • Page 110: Figure 6-11.Add Raw Ip Filter

    Chapter 6: Configuring Advanced Features Step Action From the Firewall Port Filters: External-Internal screen (Figure 6-9 on page 6-10), click Add Raw IP Filter. Figure 6-11 is displayed. Figure 6-11. Add Raw IP Filter Configure the following parameters for each session: •...

  • Page 111: Figure 6-12.Select Add Host Validator

    Chapter 6: Configuring Advanced Features Host Validator Step Action From the Security Policy Configuration page (Figure 6-8 on page 6-9), click Host Validators. Figure 6-12 is displayed. Figure 6-12. Select Add Host Validator MM702G2-W-UM-03 6-13...

  • Page 112: Figure 6-13.Add Host Validator

    Chapter 6: Configuring Advanced Features Step Action Click Add Host Validator (Figure 6-12 on page 6-13). Figure 6-13 is displayed. Figure 6-13. Add Host Validator Configure the following parameters for each session: • Host IP Address – The format of a Host IP address is a 32-bit numeric address written as four num- bers separated by periods.

  • Page 113: Security Trigger Configuration

    Chapter 6: Configuring Advanced Features Security Trigger Configuration Step Action From the Security Interface Configuration page (Figure 6-6 on page 6-7), click Configure Trigger Configuration under Policies, Triggers, Intrusion Detection, Logging. Figure 6-14 is displayed. Figure 6-14. Security Trigger Configuration Click New Trigger (Figure 6-14).
  • Page 114 Chapter 6: Configuring Advanced Features Step Action Configure the Trigger parameters: • Transport Type – Values are TCP and UDP. Default is TCP. • Port Number Start – Start number of Port. • Port Number End – End number of Port. •...

  • Page 115: Configure Intrusion Detection

    Chapter 6: Configuring Advanced Features Configure Intrusion Detection Step Action From the Security Interface Configuration page (Figure 6-6 on page 6-7), click Configure Intrusion Detection under Policies, Triggers, Intrusion Detection, Logging. Figure 6-17 is displayed. Figure 6-16. Security Trigger Configuration Configure the Intrusion Detection parameters: •...

  • Page 116: Security Logging Configuration

    Chapter 6: Configuring Advanced Features Security Logging Configuration Step Action From the Security Interface Configuration page (Figure 6-6 on page 6-7), click Configure Security Logging under Policies, Triggers, Intrusion Detection, Logging. Figure 6-17 is displayed. Figure 6-17. Security Logging Configure the Security Event Logging States for each parameter: •...

  • Page 117: Add Zipb

    Chapter 6: Configuring Advanced Features ZIPB Step Action Select Configuration|Advance|ZIPB to access the Zero Installation PPP Bridge (ZIP) Advanced Configuration page (Figure 6-18). Figure 6-18. ZIPB Advanced Configuration MM702G2-W-UM-03 6-19...
  • Page 118 Chapter 6: Configuring Advanced Features Step Action Configure the ZIPB parameters. At a minimum, ZIPB needs to link one LAN interface and one WAN interface. If no interfaces are chosen, ZIPB will automatically use the first suitable interfaces it finds. ZIPB will also do this if you choose an IP interface incorrectly.

  • Page 119: Add Router Entries

    Chapter 6: Configuring Advanced Features OUTER NTRIES A router provides a defined path from one host or network to a destination host or network. This type of route is manually entered as a fixed path, as contrasted to a dynamic route which is automatically determined and learned (e.g., RIP).

  • Page 120: Ip Routes

    Chapter 6: Configuring Advanced Features IP Routes Step Action Select Configuration|Advance|Router|IP Routes to access the Edit Routes page (Figure 6-20). Figure 6-20. IP Routes 6-22 MM702G2-W-UM-03...

  • Page 121: Figure 6-21.Create Ip Route

    Chapter 6: Configuring Advanced Features Step Action To add a new IP Interface, do the following: a. On the IP Edit page (Figure 6-20 on page 6-22), click Create New IP Route. Figure 6-21 displayed. Figure 6-21. Create IP Route b.

  • Page 122: Rip

    Chapter 6: Configuring Advanced Features Step Action Select Configuration|Advance|Router|RIP to access the RIP Configuration page (Figure 6-22). Figure 6-22. RIP 6-24 MM702G2-W-UM-03...

  • Page 123: Figure 6-23.Edit Rip Information

    Chapter 6: Configuring Advanced Features Step Action To edit the RIP Information, do the following: a. On the RIP Configuration page (Figure 6-22 on page 6-24), click Edit the Attributes. Figure 6-23 displayed. Figure 6-23. Edit RIP Information b. Edit the following RIP information: –...

  • Page 124: Bridge

    Chapter 6: Configuring Advanced Features RIDGE Global Setting Step Action Select Configuration|Advance|Bridge|Global Setting to access the Bridge Main Page (Figure 6-24). Figure 6-24. Bridge Main Page To edit the Filter Age (in seconds), type new values and click Set Value. Default is 300 seconds. To edit the Traffic Class Mapping, choose valid values Disabled, Enabled or Priority Based.

  • Page 125: Figure 6-25.Unicast Source Mac Filtering Configuration

    Chapter 6: Configuring Advanced Features Step Action To edit the Unicast Source MAC Filtering Configuration, do the following: a. On the Bridge Main Page (Figure 6-24 on page 6-26), click Unicast Source MAC Filtering Config- uration. Figure 6-25 is displayed. Figure 6-25.

  • Page 126: Figure 6-27.Unicast Destination Mac Filtering Configuration

    Chapter 6: Configuring Advanced Features Step Action Configure the following parameters: • Name – Assign a Name. • Receive Port – Values are interface and WAN session names. Receive port is referenced from the session names. • MAC Address – Values are 6 hexadecimal pairs separated by a colon (e.g., 00:20:2b:01:02:03). •...

  • Page 127: Figure 6-28.Create New Entry

    Chapter 6: Configuring Advanced Features Step Action Click Create New Entry. Figure 6-28 is displayed. Figure 6-28. Create New Entry Configure the following parameters: • Name – Assign a Name. • Destination MAC Address – Values are 6 hexadecimal pairs separated by a colon (e.g., 00:20:2b:01:02:03).

  • Page 128: Figure 6-29.Multicast Filtering Entry Configuration

    Chapter 6: Configuring Advanced Features Step Action To edit the Multicast Filtering Entry Configuration, do the following: a. On the Bridge Main Page (Figure 6-24 on page 6-26), click Multicast Filtering Entry Configura- tion. Figure 6-29 is displayed. Figure 6-29. Multicast Filtering Entry Configuration 6-30 MM702G2-W-UM-03...

  • Page 129: Figure 6-30.Create New Entry

    Chapter 6: Configuring Advanced Features Step Action Click Create New Entry. Figure 6-30 is displayed. Figure 6-30. Create New Entry Configure the following parameters: • Name – Assign a Name. • Multicast Learning Type – Default is HVM. • MAC Address – Values are 6 hexadecimal pairs separated by a colon (e.g., 00:20:2b:01:02:03). Click OK to add the parameters or click Reset to keep the current settings.

  • Page 130: Figure 6-31.Forward All/Unregistered Configuration

    Chapter 6: Configuring Advanced Features Step Action To edit the Forward All/Unregistered Configuration, do the following: a. On the Bridge Main Page (Figure 6-24 on page 6-26), click Forward All/Unregistered Configura- tion. Figure 6-31 is displayed. Figure 6-31. Forward All/Unregistered Configuration 6-32 MM702G2-W-UM-03...

  • Page 131: Figure 6-32.Add An Egress Port

    Chapter 6: Configuring Advanced Features Step Action To edit/add an Egress Port, click Edit. Figure 6-32 is displayed. Figure 6-32. Add an Egress Port Configure the following parameter: • Name – Assign a Name. Click OK to add the parameters or click Reset to keep the current settings. MM702G2-W-UM-03 6-33...

  • Page 132: Figure 6-33.Edit Bridge Interface Configuration

    Chapter 6: Configuring Advanced Features Step Action To edit the Bridge Interface Configuration, do the following. This configuration is used for VLAN and for Priority Queueing. a. On the Bridge Main Page (Figure 6-24 on page 6-26), click Interface Configuration. Figure 6-33 displayed.

  • Page 133: Figure 6-34.Priority Map

    Chapter 6: Configuring Advanced Features Step Action On the Bridge Interface Configuration page (Figure 6-33 on page 6-34), click Priority Map. Figure 6-34 displayed. Figure 6-34. Priority Map Configure the following parameter: • Traffic Classes – Valid values are 0-8 Default is 8. •...

  • Page 134: Vlan Configuration

    Chapter 6: Configuring Advanced Features VLAN Configuration Step Action Select Configuration|Advance|Bridge|VLAN Configuration to access the VLAN Configuration Page (Figure 6-35). Figure 6-35. VLAN Configuration Page 6-36 MM702G2-W-UM-03...

  • Page 135: Figure 6-36.Vlans

    Chapter 6: Configuring Advanced Features Step Action To create a New VLAN configuration, do the following. By default, Name of Default VLAN is DefaultVlan, Default FDB Name is DefaultFdb, Default VLAN ID is 1 and Ethernet and Bridged WAN interface are part of Untagged ports.

  • Page 136: Figure 6-37.Create A New Vlan

    Chapter 6: Configuring Advanced Features Step Action On the VLANs page (Figure 6-36 on page 6-37), click Create New VLAN. Figure 6-37 is displayed. Figure 6-37. Create a New VLAN Configure the following parameters: • Name – Name is an alphanumeric name. Default is DefaultVlan. •...

  • Page 137: Figure 6-38.Edit Tagged Port

    Chapter 6: Configuring Advanced Features Step Action To edit a tagged port, on the VLANs page (Figure 6-36 on page 6-37), click Edit. Figure 6-38 is displayed. Figure 6-38. Edit Tagged Port Configure the following parameters: • Name – Assign a name. •...

  • Page 138: Figure 6-39.Edit Untagged Port

    Chapter 6: Configuring Advanced Features Step Action To edit an untagged port, on the VLANs page (Figure 6-36 on page 6-37), click Edit. Figure 6-39 displayed. Figure 6-39. Edit Untagged Port Configure the following parameters: • bri-eth – Name can be deleted. •...

  • Page 139: Spanning Tree

    Chapter 6: Configuring Advanced Features PANNING Spanning tree eliminates loops in a LAN topology, ensuring there is only one path (or link) between any two nodes in a bridged network. Use spanning tree protocol (STP) when RFC 1483-Bridge protocol is assigned to either or both of the following: •...
  • Page 140 Chapter 6: Configuring Advanced Features Step Action Enter the following parameters to enable STP for bridging sessions: – Spanning Tree Select True to activate the STP for all RFC 1483-Bridge sessions and LAN Port. False turns off STP for all modem bridging sessions and LAN Port. Default is False. –...

  • Page 141: Unicast Destination Mac Filtering

    Chapter 6: Configuring Advanced Features MAC F NICAST ESTINATION ILTERING Step Action Select Configuration|Advance|Bridge|Unicast Destination MAC Filtering to access the Unicast Destination MAC Filtering page (Figure 6-41). Figure 6-41. Unicast Destination MAC Filtering MM702G2-W-UM-03 6-43...

  • Page 142: Figure 6-42.Create Destination Mac Based Unicast Filtering Entry

    Chapter 6: Configuring Advanced Features Step Action To add a new Unicast Destination MAC Filtering entry, do the following: a. On the Unicast Destination MAC Filtering page (Figure 6-41 on page 6-43), click Create New Entry. Figure 6-42 is displayed. Figure 6-42.

  • Page 143: Unicast Source Mac Filtering

    Chapter 6: Configuring Advanced Features MAC F NICAST OURCE ILTERING Step Action Select Configuration|Advance|Bridge|Unicast Source MAC Filtering to access the Unicast Source MAC Filtering Entry page (Figure 6-43). Figure 6-43. Unicast Source MAC Filtering Entry MM702G2-W-UM-03 6-45...

  • Page 144: Figure 6-44.Create Unicast Source Mac Filtering Entry

    Chapter 6: Configuring Advanced Features Step Action To add a new Unicast Source MAC Filtering Entry, do the following: a. On the Unicast Source MAC Filtering page (Figure 6-43 on page 6-45), click Create New Entry. Figure 6-44 is displayed. Figure 6-44.

  • Page 145: Dhcp Server

    Chapter 6: Configuring Advanced Features DHCP S ERVER Add DHCP Server Interface Step Action Select Configuration|Advance|DHCP|DHCP Server to access the DHCP Server page (Figure 6-45). Figure 6-45. DHCP Server To enable the DHCP Server, click Enable. To disable the DHCP Server, click Disable. Default is Disable.

  • Page 146: Figure 6-46.Create New Subnet

    Chapter 6: Configuring Advanced Features Step Action To create a new Subnet, click on Create New Subnet under Add New Interface (Figure 6-45 on page 6-47). Figure 6-46 is displayed. Figure 6-46. Create New Subnet Enter the following parameters for this subnet: –...

  • Page 147: Figure 6-47.Create New Fixed Host

    Chapter 6: Configuring Advanced Features Step Action Enter the following parameters for the IP address to be available on this subnet: – Start of Address Range – 192.168.0.0. – End of Address Range – 192.168.255.255 (example). – Use as Default Range – Click box to use as default range. Enter the DNS Server Option Information: –...

  • Page 148: Add A Dhcp Relay

    Chapter 6: Configuring Advanced Features Add a DHCP Relay Step Action Select Configuration|Advance|DHCP|DHCP Relay to access the DHCP Relay page (Figure 6-47). Figure 6-48. DHCP Relay To enable the DHCP Relay, click Enabled. To disable the DHCP Relay, click Disabled. Default is Disabled.

  • Page 149: Dns

    Chapter 6: Configuring Advanced Features DNS Client Servers Step Action Select Configuration|Advance|DNS|DNS Client to access the DNS Client page (Figure 6-49). Figure 6-49. DNS Client Servers Under DNS Servers, add a new server and click Add. Under Domain Search Order, type the domain search and click Add. MM702G2-W-UM-03 6-51...

  • Page 150: Dns Relay

    Chapter 6: Configuring Advanced Features DNS Relay Step Action Select Configuration|Advance|DNS|DNS Relay to access the DNS Relay page (Figure 6-50). Figure 6-50. DNS Relay 6-52 MM702G2-W-UM-03...

  • Page 151: Figure 6-51.Dns Relay Local Lan Database

    Chapter 6: Configuring Advanced Features Step Action To access the DNS Relay Local LAN Database, click on DNS Relay LAN Database (Figure 6-50 on page 6-52. Figure 6-51 is displayed. Figure 6-51. DNS Relay Local LAN Database Type the LAN Domain Name. Click Apply. MM702G2-W-UM-03 6-53...

  • Page 152: Figure 6-52.Create/View Dns Relay Local Lan

    Chapter 6: Configuring Advanced Features Step Action To create or view a LAN database entry for IPv4 Hosts, click on Create/View LAN Database for IPv4 Hosts (Figure 6-51 on page 6-53). Figure 6-52 is displayed. Figure 6-52. Create/View DNS Relay Local LAN Type the Host Name and IP Address.

  • Page 153: Igmp

    Chapter 6: Configuring Advanced Features IGMP IGMP Snooping is the process of listening to IGMP traffic. IGMP snooping is a feature that allows the switch to "listen in" on the IGMP conversation between hosts and routers by processing the layer 3 packets IGMP packets sent in a multicast network.

  • Page 154: Figure 6-54.Add An Interface As The Multicast Router

    Chapter 6: Configuring Advanced Features Step Action Enter the following parameters for the IGMP Snoop Configuration: – IGMP Snoop – Values are Disable, Enable and Drop. Default is Disable. – Last Member Query Interval – Total queries. Default is 1. –...

  • Page 155: Igmp Proxy Groups

    Chapter 6: Configuring Advanced Features IGMP Proxy Groups Step Action Select Configuration|Advance|IGMP|IGMP Groups to access the IGMP Group Table page (Figure 6-55). Figure 6-55. IGMP Group Table MM702G2-W-UM-03 6-57...

  • Page 156: Ports

    Chapter 6: Configuring Advanced Features ORTS Ethernet Step Action Select Configuration|Advance|Ports|Ethernet to access the Ethernet Port Configuration page (Figure 6-56). Figure 6-56. Ethernet Port Configuration Enter the following parameters for the Ethernet Port Configuration: – Auto Negotiation – Values are True and False. Default is True. –...

  • Page 157: Ports

    Chapter 6: Configuring Advanced Features ORTS SHDSL Step Action Select Configuration|Advance|Ports|SHDSL to access the SHDSL Port Configuration page (Figure 6-57). Figure 6-57. SHDSL Port Configuration Configure the Admin State parameter (Figure 6-57). Set to Disable. Click Apply. MM702G2-W-UM-03 6-59...
  • Page 158 Chapter 6: Configuring Advanced Features Step Action Configure the following parameters: • Mode The four mode options are: CPE-2Wire, CPE-GS4Wire, CO-2Wire, and CO-GS4Wire. The default for MM702G2-W is CPE-2Wire. When the modem is connected to a service provider through a DSLAM, the operating mode is Remote (default setting).
  • Page 159 Chapter 6: Configuring Advanced Features Step Action • PSD Mode (cont) The Power Spectral Density (PSD) plots the variations of signal power with signal frequency for the G.shdsl transmission between the modem and the DSLAM or the modem and another modem. Symmetric PSD indicates that the PSD mask for both sides of the transmission (the CO- and remote- side) are the same (symmetric).
  • Page 160 Chapter 6: Configuring Advanced Features Page Intentionally Left Blank 6-62 MM702G2-W-UM-03...

  • Page 161: Chapter 7: Maintenance

    Chapter AINTENANCE ELNET CCESS Step Action Select Maintenance|Telnet Access to access the Edit Telnet Access page (Figure 7-1). Figure 7-1. Edit Telnet Access Click Enabled or Disabled. To disable Telnet access to Modem, select Disabled. The default is Enabled. Click Apply to change the parameters or click Reset to keep the current settings. MM702G2-W-UM-03...

  • Page 162: Management Ip

    Chapter 7: Maintenance ANAGEMENT Step Action Select Maintenance|Management IP to access the Edit Management IP page (Figure 7-2). Figure 7-2. Edit Management IP Type Management IP value. If an IP address is configured for a Management IP field, only that management PC or Host with the IP address can manage the modem.

  • Page 163: Firmware Update

    Chapter 7: Maintenance IRMWARE PDATE Using the Web interface HTTP Upgrade capability, you can upgrade the software image (.tar). To complete an upgrade, browse to the latest image on your PC or the network drive and then select it. The software update process takes about 90 seconds to complete and after the update, the user IMPORTANT must reboot the modem manually.

  • Page 164: Backup/Restore

    Chapter 7: Maintenance ACKUP ESTORE Step Action Select Maintenance|Backup/Restore to access the Backup/Restore Configuration page (Figure 7-4). Figure 7-4. Backup/Restore Configuration To backup your configuration, click Backup to navigate to the location where you want to backup. Follow the online instructions to complete the procedure. To restore your configuration, click Browse to select the backup configuration file.

  • Page 165: Restart/Set Factory Default

    Chapter 7: Maintenance ESTART ACTORY EFAULT When you configure the modem, you change the factory default settings to new values. You can return these parameters to their default values to provide a known starting point if you are troubleshooting or you simply want to configure new parameters.

  • Page 166: Reset To Factory Defaults Using The Reset Button

    Chapter 7: Maintenance Reset to Factory Defaults using the Reset Button The reset button on the back panel of your modem is provided to reboot the modem without the need to remove power. Under normal circumstances, you will not have to use the reset button. On rare occasions, however, your modem may not respond.

  • Page 167: Chapter 8: Implementing A Point-To-Point Lan Extension

    LAN extension. The ADC modems comply with the standard G.shdsl data rate range of 192 Kbps to 2304 Kbps in 2-wire mode and data rate range of 384 Kbps to 4608 Kbps in 4-wire mode. Additionally, rates down to 64 Kbps are supported only when using the G.shdsl modem in single-pair, point-to-point mode for a LAN extension application.

  • Page 168: Configure For Central Office (Co) Mode

    Chapter 8: Implementing a Point-To-Point LAN Extension Configure for Central Office (CO) Mode Step Action Select Configuration|SHDSL to access the SHDSL Port Configuration page (Figure 8-1). Figure 8-1. SHDSL Port Configuration—Configure for Central Office (CO) Mode In the Mode box, select CO-2Wire or CO-GS4Wire to set up this modem for this mode. Click Apply.

  • Page 169: Change The Lan Ip Address For The Central Office Modem

    Chapter 8: Implementing a Point-To-Point LAN Extension Change the LAN IP Address for the Central Office Modem Because the Central Office and Remote modems by default have the same IP Address 10.0.0.1 point-to-point application, you must change the IP address for the Central Office modem or Remote Modem. Step Action Select Configuration|LAN Connections to access the LAN Connections page...

  • Page 170: Figure 8-3. Lan Port

    Chapter 8: Implementing a Point-To-Point LAN Extension Step Action To change the IP address for the LAN Port, click on Change LAN Port IP Address from the LAN Connections page (Figure 8-2 on page 8-3). Figure 8-3 is displayed. Figure 8-3. LAN Port In the IP address box, enter 192.168.0.1.

  • Page 171: Complete A Custom Configuration

    Chapter 8: Implementing a Point-To-Point LAN Extension OMPLETE A USTOM ONFIGURATION If you implement custom configuration where you do not use factory default parameters for your modems, you will need to make changes to the configuration on both the Remote and the Central Office modem. The following sections provide configuration changes for the Remote modem and then for the Central Office modem.

  • Page 172: Figure 8-4. Shdsl Port Configuration-Configure Remote Mode

    Chapter 8: Implementing a Point-To-Point LAN Extension Configure the Remote Mode Step Action Select Configuration|SHDSL to access the SHDSL Port Configuration page (Figure 8-4). Figure 8-4. SHDSL Port Configuration—Configure Remote Mode In the Mode box, select CPE-2wire or CPE-GS4Wire to configure the modem for this mode. Click Apply.

  • Page 173: Figure 8-5. Wan Configuration

    Chapter 8: Implementing a Point-To-Point LAN Extension Configure the Remote WAN Step Action Select Configuration|WAN Connections to access the WAN Configuration page (Figure 8-5). Figure 8-5. WAN Configuration Select Create a new service (Figure 8-5). Figure 8-6 is displayed. Figure 8-6. WAN Connection: Create Service MM702G2-W-UM-03...

  • Page 174: Figure 8-7. Rfc 1483 Bridged Session

    Chapter 8: Implementing a Point-To-Point LAN Extension Step Action Click on RFC 1483 Bridged and Configure (Figure 8-6 on page 8-7). Figure 8-7 is displayed. Figure 8-7. RFC 1483 Bridged Session In the Session Name box, assign a name to this session. In the Virtual Path ID (VPI 0 - 4,095) box, enter the Virtual Path ID.

  • Page 175: Figure 8-8. Lan Configuration-Configure Remote Lan

    Chapter 8: Implementing a Point-To-Point LAN Extension Configure the Remote LAN Step Action Select Configuration|LAN Connections to access the LAN Connections page (Figure 8-8). Figure 8-8. LAN Configuration—Configure Remote LAN In the LAN Protocol box, confirm that the protocol is set to Bridged. Any device (such as a PC) connecting to the modem LAN interface loses its connection when the modem LAN IP address is changed.

  • Page 176: Figure 8-9. Lan Port

    Chapter 8: Implementing a Point-To-Point LAN Extension Step Action To change the IP address for the LAN Port, click on Change LAN Port IP Address (Figure 8-8 on page 8-9). Figure 8-9 is displayed. Figure 8-9. LAN Port In the IP Address box, enter an available IP address on your subnet. Click Apply.

  • Page 177: Configure The Central Office Modem

    Chapter 8: Implementing a Point-To-Point LAN Extension Configure the Central Office Modem To configure the central-office modem, you need to change the following settings: • Mode for the modem, (see “Configure the Central Office Mode” on page 8-11) • WAN parameters, (see “Configure the Central Office WAN”...

  • Page 178: Figure 8-11.Wan Configuration

    Chapter 8: Implementing a Point-To-Point LAN Extension Configure the Central Office WAN Step Action Select Configuration|WAN Connections to access the WAN Configuration page (Figure 8-11). Figure 8-11. WAN Configuration Select Create a new service (Figure 8-11). Figure 8-12 is displayed. Figure 8-12.

  • Page 179: Figure 8-13.Rfc 1483 Bridged Session

    Chapter 8: Implementing a Point-To-Point LAN Extension Step Action Click on RFC 1483 Bridged and Configure (Figure 8-12 on page 8-12). Figure 8-13 is displayed. Figure 8-13. RFC 1483 Bridged Session In the Session Name box, assign a name to this session (can be the same as the Remote modem). In the Virtual Path ID (VPI 0 - 4,095) box, enter the Virtual Path ID.

  • Page 180: Figure 8-14.Lan Configuration-Configure Remote Lan

    Chapter 8: Implementing a Point-To-Point LAN Extension Configure the Central Office LAN Step Action Select Configuration|LAN Connections to access the LAN Connections page (Figure 8-14). Figure 8-14. LAN Configuration—Configure Remote LAN In the LAN Protocol box, confirm that the protocol is set to Bridged. Any device (such as a PC) connecting to the modem LAN interface loses its connection when the modem LAN IP address is changed.

  • Page 181: Figure 8-15.Lan Port

    Chapter 8: Implementing a Point-To-Point LAN Extension Step Action To change the IP address for the LAN Port, click on Change LAN Port IP Address (Figure 8-14 on page 8-14). Figure 8-15 is displayed. Figure 8-15. LAN Port In the IP Address box, enter an available IP address on your subnet. Click Apply.

  • Page 182: Verify Connectivity

    Chapter 8: Implementing a Point-To-Point LAN Extension ERIFY ONNECTIVITY After you have performed each of the previous configuration changes, verify back-to-back communication by passing traffic over the WAN session. For example, set up a PC on the LAN-side of the Remote modem and another PC on the LAN-side of the Central Office modem.

  • Page 183: Appendix A: Specifications

    Appendix PECIFICATIONS The MM702G2-W is a 1-pair/2-pair SHDSL modem that takes advantage of G.shdsl technology by offering fixed and rate-adaptive communication at equal rates going both upstream and downstream until 4608 Kbps is reached. In addition, the modem also provides sessions for precise control of security, performance and management of users and resources per session;...

  • Page 184: Data Specifications

    Appendix A: Specifications • IEEE 802.1q (VLAN) • IEEE 802.1p (Priority Queueing) • Secondary IP Address • Virtual IP Interface • Management IP Control • Telnet Enable/Disable PECIFICATIONS • The MM702G2-W modems allow larger packet sizes (Maximum: 1536 Bytes with CRC). •...
  • Page 185 Appendix A: Specifications • Remote Management – Software Upgrade – HTTP download into built-in flash memory – Backup/Restore Configuration • Encapsulation – When you activate RFC 1483 system mode, you can select WAN encapsulation as VC multiplexing for some sessions and LLC encapsulation for other sessions. •...

  • Page 186: Default Session Parameter Values

    Appendix A: Specifications EFAULT ESSION ARAMETER ALUES Web Configuration Factory Default System|User Administration|Edit User User(1) admin Password(1) password Access level(1) superuser Comment(1) default admin user User(2) Password(2) password Access level(2) engineer Comment(2) user at ISP User(3) user Password(3) password Access level(3) default Comment(3) read/view only access...
  • Page 187 Appendix A: Specifications Web Configuration Factory Default Edit RIP Versions Accept V1 False Accept V2 False Send V1 False Send V2 False Send Multicast False Edit NAT Nat Enabled False Configuration|WAN Connections Session Name rfc0-35 IP/Bridge Interface Name bri-rfc0-35 Type RFC1483 Bridged Port SHDSL...
  • Page 188 Appendix A: Specifications Web Configuration Factory Default Edit ATM Channel 5500 ATM QOS Burst Tolerance Max Cell Rate Max Burst Size Sustainable Cell Rate Packet Priority Levels Edit Bridge Interface Leave Mode Normal IGMP Port State Disable Ether Filter Type Ingress Filtering Status False Frame Access Type...
  • Page 189 Appendix A: Specifications Web Configuration Factory Default Edit Spanning Bridge Interface Priority Path Cost Configuration|Advance|Proxy ARP|Create New Proxy ARP Entry Exclude False Configuration|Advance|SNMP Community|Create a New Community Access Level Read Configuration|Advance|Security Security State Security Disabled Firewall Disabled Intrusion Detection Enabled Disabled Security Level Block All...
  • Page 190 Appendix A: Specifications Web Configuration Factory Default Security Trigger Configuration New Trigger Transport Type Secondary Port Number Start 1024 Secondary Port Number End 65535 Allow Mulitple Hosts Allow Enable Session Chaining Allow Enable UDP Session Chaining Allow Binary Address Replacement Allow Address Translation Type None...
  • Page 191 Appendix A: Specifications Web Configuration Factory Default WAN Interface None LAN IP Address Spoof Method Top of Subnet Manual LAN IP Address 10.0.0.1 LAN Subnet Mask Selection Method Natural Manual LAN Subnet Mask 255.255.0.0 LAN DHCP Server Lease Time 40 seconds LAN PC Power Down Time 120 seconds Configuration|Advance|Router|IP Interface...
  • Page 192 Appendix A: Specifications Web Configuration Factory Default Acceptable Frame Type CFG Enabled Ingress Filtering CFG Enabled Filter Age (in Seconds) Traffic Class Mapping Disabled Unicast Source MAC Filtering Configuration|Create New Entry Entry Type SRC Static Unicast Destination MAC Filtering Configuration|Create New Entry Entry Type Dest Static Multicast Filtering Entry Configuration|Create New Multicast Entry...
  • Page 193 Appendix A: Specifications Web Configuration Factory Default User Priority6 Regenerated Priority6 User Priority7 Regenerated Priority7 Regenerated Priority0 Traffic Class0 Regenerated Priority1 Traffic Class1 Regenerated Priority2 Traffic Class2 Regenerated Priority3 Traffic Class3 Regenerated Priority4 Traffic Class4 Regenerated Priority5 Traffic Class5 Regenerated Priority6 Traffic Class6 Regenerated Priority7 Traffic Class7...
  • Page 194 Appendix A: Specifications Web Configuration Factory Default Configuration|Advance|Bridge|Spanning Tree Spanning False Priority 32768 Forward Delay Hello Time Maximum Age Configuration|Advance|Bridge|Unicast Destination MAC Filtering Create New Entry Entry Type Dest Static Configuration|Advance|Bridge|Unicast Source MAC Filtering Create New Entry Entry Type Src Static Configuration|Advance|DHCP|DHCP Server DHCP Server Disable...
  • Page 195 2-Wire: 2304(Kbps), 4-Wire: 4608(Kbps) Startup Margin -10(dB) PSD Mode Symmetric SNR Margin Limit 6(dB) Reset Defaults False Admin State Enable Maintenance|Telnet Access Telnet Access Enabled Maintenance|Management IP Management IP 0.0.0.0 SNMP Sysconfig sysDescr ADC SHDSL Megabit Modem sysContact http://www.adc.com sysName MM702G2-W MM702G2-W-UM-03 A-13...

  • Page 196: Hardware Specifications

    Appendix A: Specifications ARDWARE PECIFICATIONS • LED • Power – MM702G2-W using 120 VAC, 60 Hz • Operating Temperature of the modem: 0~50°C • Power Adapter Spec: – Input: 100~240 VAC, 50/60 Hz, 0.3 A – Output: 6 VDC, 2 A •...

  • Page 197: Connector Pinouts

    Appendix A: Specifications ONNECTOR INOUTS The following sections provide the pinout information for the various modem connectors. • SHDSL Port (RJ-11) Table A-1 shows the signal on each pin of the SHDSL port for a 2-wire G.shdsl application. The connector for this interface is an RJ-11.

  • Page 198: Table A-3.10/100Base-T Port

    Appendix A: Specifications • 10/100Base-T Port (RJ-45) Table A-3 shows the signal on each pin of the 10/100Base-T port connector when the switch is in either the MDI or the MDI-X position. The connector for this interface is an RJ-45. See Connect Cables on page 1-3 for the location of this port.

  • Page 199: Rate Vs Reach

    Appendix A: Specifications ATE VS EACH The following rate versus reach charts show values per each G.shdsl loop (Loop A or Loop B). MM702G2-W-UM-03 A-17...
  • Page 200 Appendix A: Specifications Page Intentionally Left Blank A-18 MM702G2-W-UM-03...

  • Page 201: Appendix B: Product Support

    UPPORT ADC Customer Service Group provides expert pre-sales support and training for all of its products. Technical support is available 24 hours a day, 7 days a week by contacting the ADC Technical Assistance Center. Sales Assistance: 800.366.3891 Quotation Proposals, Ordering and Delivery General, and Product Information Systems Integration: 800.366.3891...
  • Page 202 Appendix B: Product Support Page Intentionally Left Blank MM702G2-W-UM-03...
  • Page 203 Glossary Symbol 10/100Base-T – The Institute of Electrical and Electronic Engineers (IEEE) 802.3 specification for Ethernet over UTP cable. AAL2 – ATM Adaptation Layer 2. Used for compressed voice and video that is intolerant of delay. This layer is used by xDSL technology. AAL5 –...
  • Page 204 Glossary G.shdsl – Symmetrical High-Speed Digital Subscriber Line. Gateway – A device (generally a router) that provides translation services to allow communication between two dissimilar networks. IGMP – Internet Group Management Protocol is a communications protocol used to manage the membership of Internet Protocol multicast groups.
  • Page 205 Glossary QoS – Quality of Service is the configured traffic parameters that are assigned to a virtual circuit, which specifies how quickly and how accurately data is transferred from the sender to the receiver. RFC – Request For Comment is a series of notes that contain surveys, measurements, ideas, techniques, and observations, as well as proposed and accepted TCP/IP protocol standards.
  • Page 206 Glossary VCI – Virtual Channel Identifier is a 16-bit field addressing identifier in the header of an ATM cell used to route cell traffic. It identifies a particular VC link for a given VP. VCMUX – Virtual Channel Multiplexer-based encapsulation used for networks with large numbers of virtual channels making it practical to carry a single protocol per virtual channel.
  • Page 207 The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by ADC voids the user’s warranty. All wiring external to the products should follow the provisions of the current edition of the National Electrical Code.
  • Page 208 World Headquarters ADC Telecommunications, Inc. PO Box 1101 Minneapolis, MN 55440-1101 USA For Technical Assistance Tel: 800.366.3891 ® Megabit Modem MM702G2-W V5.x User Manual Product Catalog: MM702G2-W Document Number: MM702G2-W-UM-03 ´.0q¶0R¨ 1416810...

Table of Contents