GRAUPNER mc-16 Programming Manual page 69

Select model type
Use the  or  keys of the left or right four-way button
to select the basic model type then tap on the centre
SET key of the right four-way button. This initializes
the selected model memory with the selected model
type and the display will return to the base screen. The
memory location is now accordingly occupied.
Changing over to another model type is still possible if
you fi rst erase this memory location (»Copy / Erase«
menu, page 72).
Notes:
• If the currently active model memory is to
be erased then immediately after the
erase action one of the two model types,
"Winged" or "Heli" must be defi ned. You cannot
avoid this selection even if you switch the trans-
mitter off. Only afterward the undesired occupation
of that model memory erase from another memory
location.
If a non-active memory location is erased, it will
subsequently be marked as "free" in the
"Model select" menu.
• After the selected model memory is initialized with
the desired model type, the display will switch to
the base screen of the freshly occupied model
memory. At this time the warning ...
BIND. N/A
OK
... will appear for several seconds as notifi ca-
tion that a binding connection to a receiver is "not
available". A brief tap on the centre
right four-way button will cause a direct jump to
the appropriate option:
01
02 free
 
03
free
 
04
free
 
05 free
 
06 free
 
Further details about binding a receiver can be
found on page 80 or 90.
• The "BIND n/a" warning closes automatically, af-
ter which the following warning also appears for a
few seconds ...
F a i l S a f e
s e t u p
t . b . d .
... will appear (also for just a few seconds) to indi-
cate that no fail safe settings have yet been made.
More about this can be found on page 216.
• If the screen should display the warning ...
T h r
t o o
h i g h !
... appears, then move the throttle / pitch control
stick, in the helicopter type if necessary, the limit-
er, by default the right side proportional rotary slid-
er SD2, in the idle position.
Until this happens, the RF module of the transmit-
ter remains switched off.
Whether or not this warning appears also depends
on the settings selected for the "Motor on C1" and
"Pitch min." options in the »Model type« menu,
see page 98, or »Helicopter type« menu, see
page 102.
For winged aircraft models, select "None" to deac-
SET key of the
tivate this message if you have no motor to enter.
• If the transmitter already has occupied mod-
el memories then sub-menus of the »Copy /
Erase« menu will display a pictograph of the se-
M E 12
lected model type at the respective memory loca-
tion followed by a blank line or the model name
which was entered in the »Basic settings, mod-
el« menu, page 78 or 88.
• If battery voltage is too low, the model switchover
cannot be made due to reasons of safety. An ap-
propriate message will appear in the screen:
As a basic principle, there are four different ways to as-
sign the four control functions, aileron, elevator, rudder
and throttle or brake fl aps for winged models as well
as rolling, pitching, tail rotor and throttle/pitch for heli-
copter models, to the two sticks. Just which of these
methods is used depends on the preferences of the in-
dividual model pilot. This function is set for the currently
active model memory in the "Stick mode" line of the
»Basic settings, model« menu, page 78 or <?>:
If this setting is desired as a default for future models,
the setting can also be entered into the »General ba-
sic settings« menu, page 267:
Program description - Loading a new memory location
n o t p o s s i b l e n o w
v o l t a g e t o o l o w
Base setup model
Mod.name
Stick mode 1
module HoTT n/a n/a
DSC Output PPM10
BD1 BD2
69