GRAUPNER mc-16 Programming Manual page 267

Basic settings
Voice Vol 7 fr
Move desired
Vario Vol 7 fr
control adj.
Beeps Vol 3 fr
Own
SEL SEL
Now move the desired control, for example, the right
proportional slider Sl2. Afterward, this slider can be
used anytime to incrementally regulate volume for the
selected group between 0 and 10.
Following a simultaneous tap on the  or  keys
of the right four-way button (CLEAR), the display will
return to its "fr" default value.
via three position switch
Use the selection keys on the left or right four-way but-
ton to move the marker frame to the column above the
switch symbol at the display's lower edge then briefly
tap the centre SET key of the right four-way button.
The message shown below will then appear in the
display:
Basic settings
Voice Vol 7 fr
M o v e d e s i r e d s w i t c h
Vario Vol 7 fr
t o O N p o s i t i o n
Beeps Vol 3 fr
( e x t . s w i t c h : S E T )
Own
SEL SEL
Now, assign a switch as described in the section
"Physical control, switch and control switch assign-
ments" on page 60. Ideally a self-neutralizing three
position switch, e. g. like that offered by Graupner
under No. 33001.5. Afterward, this switch can be used
anytime to incrementally regulate volume for the se-
lected group between 0 and 10.
Following a simultaneous tap on the  or  keys
of the right four-way button (CLEAR), the display will
return to its "---" default value.
Own(er)
–––
–––
Voice Vol
–––
Vario Vol
Beeps Vol
Own
Up to 15 characters can be used to specify the owner's
name. Change to the next screen page (
tap on the centre
! " # $ % & ' ( ) + , – . / 0 1 2 3
4 5 6 7 8 9 : ;
F G H I J K L M N O P Q R S T U V W X
Y Z [ ¥ ] ^ _ ` a
Owner H-J
Select the desired characters with the selection keys
of the left four-way button. With a brief tap on the 
selection key of the right four-way button or its centre
SET key, move to the next position in which a char-
acter can be selected. A simultaneous tap on the 
–––
or  keys of the right four-way button (CLEAR) will
–––
place a space character at the current position.
–––
Positioning to any character position within the en-
try field can be done with the  keys of the right
touch pad.
A brief tap on the centre
button will cause a return to the previous menu page.
Basic settings
7 Cn5 –––
7 Cn6 –––
3 2 3
) with a brief
SET key of the right four-way button:
? @ A B C D E
b c d e f g h i j k
Sandb
ESC key of the left four-way
(Pre-set) Stick mode
As a basic principle, there are four different ways to as-
sign the four control functions, aileron, elevator, rudder
and throttle or brake flaps for winged models as well as
rolling, pitching, tail rotor and throttle/pitch for helicop-
ter models to the two sticks. Just which of these op-
tions is chosen depends on the individual preferences
of the individual model pilot:
Winged model stick mode
MODE 1 (Throttle at rigth stick) MODE 2 (Throttle at left stick)
elev. down full throttle full throttle
elev. up idle idle
MODE 3 (Throttle at right stick) MODE 4 (Throttle at left stick)
elev. down full throttle full throttle
elev. up idle idle
Helicopter model stick mode
MODE 1 (Throttle at right stick) MODE 2 (Throttle at left stick)
pitch axis throttle/pitch throttle/pitch
pitch axis throttle/pitch throttle/pitch
MODE 3 (Throttle at right stick) MODE 4 (Throttle at left stick)
pitch axis throttle/pitch throttle/pitch
pitch axis throttle/pitch throttle/pitch
Program description - Basic settings
elev. down
elev. up
elev. down
elev. up
pitch axis
pitch axis
pitch axis
pitch axis
267