GRAUPNER mc-16 Programming Manual page 163

"Alarm" timer
Timer1 0:00
Timer2 0:00
Timer3 0:00
Lap time/Tim tab
Lap Display
SEL SEL
The input field in the "Alarm" column is activated with a
tap on the centre SET key of the right four-way but-
ton. In this field, use the selection keys on the left or
right four-way button to define a time between 5 and
90 seconds (in 5-second increments) before zero is
reached: at this point an audible signal will be emitted,
which eliminates the need for you to check the screen
continually during the flight.
Audible signal sequence
30 s before zero: Triple beep
Single beep every two seconds
20 s before zero: Double beep
Single beep every two seconds
10 s before zero: Single beep
Single beep every second
5 s before zero: every second a single beep at a
higher frequency
zero: longer beep signal and changeover
of display presentation to inverse
video
A simultaneous tap on the  or  keys of the right
four-way button (CLEAR) will reset entry values en-
tered in the currently active field to "0 s".
Note:
If timer functionality has been changed at any
point, then the new changes to settings are
made active only after the timer(s) have been
stopped on the basic display then making a simulta-
neous tap on the  or  keys of the right four-
way button (CLEAR) to reset them.
Like the two standard timers positioned above it, this
third, phase-specific timer is reset to its starting value
0s –––
with a simultaneous tap on the  or  keys of
0s –––
the right four-way button (CLEAR). It is stopped in all
0s –––
flight phases at the same time, even if it has not been
–––
stopped separately in the other flight phases.
–––
Lap counter/timetable
On the "Lap time/tim tab" line, assign a switch only as
described in the section "Physical control, switch and
control switch assignments" on page 60. Preferably,
make use of a momentary switch, which are included
as standard equipment only in the switch panels of the
HoTT transmitters. The lap count is incre-
mc-20
mented each time by one lap while simultaneously (and
automatically) the lap time elapsed during this lap is
stopped (and recorded). This momentary switch simul-
taneously starts the stopwatch for the next lap. As the
timer is triggered, the lap or switch impulse counter is
shown highlighted:
GRAUBELE
#01
«Speed
"Time1" and "Time2" operate in the same manner; for
more details please read the section on the »Phase
settings« menu option on page 148 or 152.
Up to 99 lap times can be recorded and accessed,
each with a maximum duration of 99 minutes and 59.9
seconds.
Timer1 0:00 0s –––
Timer2 0:00 0s –––
Timer3 0:00 0s –––
Lap time/Tim tab –––
Lap Display –––
SEL
SEL
0:00
Stp
Flt 0:00
» Lap 11
0:00.0
3.9V 2:33.4
K78
2:22h M 5.5V
To stop the timer in question, tap the centre
of the left four-way button on the basic display after the
flight is over. The lap or switch impulse counter is now
shown in "normal" mode:
GRAUBELE
Stp
#01 Flt
«Speed » Lap
3.9V
K78
2:24h M
A simultaneously tap on the  or  keys of the
right four-way button at the same time (CLEAR) will
reset the counter to "00" and deletes the stored
times. However, the timers must have been stopped
before this.
Notes:
• If you have selected a normal switch to
operate the lap counter, take care to en-
sure that this switch is set to "OFF" before
touching the centre ESC key of the left four-way
button.
• If you should forget to switch off the lap counter in
a phase which is now not currently active, simply
touch the centre ESC key of the left four-way but-
ton.
To swap between the basic display and the "Lap Dis-
play" ...
Program description - Flight phase timers
ESC key
0:00
0:00
22
4:33.2 0:00.0
5.5V
163