GRAUPNER mc-16 Programming Manual page 321

The selection of "yes/no" in the "Power-on beep"
line determines whether the "recognition melody" is to
sound when the transmitter is switched off or on again.
The "Battery type" line specifi es whether the transmit-
ter is supplied with current from a "NiMH or a "Lith."
battery, and the "Battery warning" line below it speci-
fi es the voltage at which the transmitter's low-voltage
warning should trigger. Do not enter a value that is too
low here, so you have enough time to land your heli-
copter.
The setting made in the "Stick warning" line de-
termines how long the transmitter will wait after the
last actuation of an operating element before issuing
visual and acoustic warning signals to indicate it is
still switched on. Following the warning, you still have
about three minutes to actuate the transmitter so the
warning will abate. Otherwise the transmitter will switch
itself off when this time expires.
The value set in the "Touch Sense" line is a matter of
adapting the transmitter to personal preferences.
In the "DATA sel." line you can specify which abuts
the two possible data logs to the located under the
left front cover Data socket. By default, it is the data
output on the Smart-Box, No. 33700, suitable "telem-
etry" protocol.
Finally, if you are using a Bluetooth headset, you
can bind and confi gure it as described in the instruc-
tions supplied with the optional Bluetooth module, No.
33002.5; see the section entitled "BT Headset".
Once these settings have been taken care of, commis-
sioning continues with the menu ...
»Model select«
Use the selection keys to pick a free memory loca-
tion ...
01 M E 12
02 free
 
03 free
 
04 free
 
05 free
 
06 free
 
... and call it up with a brief tap on the centre
of the right touch pad. In the display which then ap-
pears, use the  key of the left or right touch pad ...
Select model type
... to select the "helicopter" model type. The display
immediately switches to the base screen if the selec-
tion is confi rmed by a brief tap on the centre
of the right touch pad.
Notes:
• If the "Select model type" option has been
opened, the process cannot be canceled.
Even if you switch off the transmitter, this
selection must be made! In any case, you
can undo this by subsequently deleting the re-
spective model memory.
• If the "Throttle too high" warning appears, it can be
erased by turning the right-side proportional rota-
ry control to its backward limit or the throttle / pitch
control stick of your transmitter to the idle or Pitch
minimum position.
• If battery voltage is too low, the model switchover
cannot be made due to reasons of safety. An ap-
(page 71) propriate message will appear in the screen:
n o t p o s s i b l e n o w
v o l t a g e
Once this fi rst hurdle is cleared, the connection of the
receiver built into the model at this model memory
must be made in the menu ...
»Base setup model«
To this end, switch to the line "module":
SET key
Base setup model
Mod.name
Stick mode
module
DSC Output
Note:
After confi rmation of the model selection in
the base screen, if you confi rm the message
appearing in the screen for a few seconds ...
key
SET
SET
... with a tap on the
this line will be accessed automatically.
"Binding type"
If your transmitter is equipped with the latest fi rmware
or has since been updated accordingly, you should
briefl y deal yet with the differences between the two
available HoTT synchronization methods before the
actual binding process. Set default "model":
Programming examples - Helicopter models
t o o l o w
(beginning on page 88)
1
HoTT n/a n/a
PPM10
BD1 BD2
BIND. N/A
OK
key of the right touch pad,
321