GRAUPNER mc-16 Programming Manual page 259

Column 4 "offset"
Multichannel 1
INPUT1 3 2
INPUT2 fr –––
INPUT3 fr –––
INPUT4 fr –––
The control centre for the given control, i. e. its zero
point, can be changed in this column. The adjustment
range lies between -100 % and +100 %.
Simultaneously tapping on the  or  keys of
the right four-way button (CLEAR) will reset the value
displayed in inverse video back to its "0 %" value.
Note:
Leave the offset setting at 0 % while making switch
assignments.
Column 5 "– travel +"
To adjust servo travel, move to the right, beyond the
"Offset" column, following the right-pointing arrow in
the bottom left-hand corner of the screen:
Multichannel 1
INPUT1 +100% +100%
INPUT2 +100% +100%
INPUT3 +100% +100%
INPUT4 +100% +100%
– travel +
Finally, transmitter control travel is set for both sides in
the column "-travel+". The range for this lies between
-100 % and +100 %. This is accomplished by moving
the associated transmitter control to the centre – if you
wish to set symmetrical travels – or in one direction or
the other in order to set "travel" separately for each
side of centre.
If the assignment is for a switch, leave the setting at the
default value of 100 %.
Receiver Graupner HoTT GR-32 attachment example
Before first time operation of the NAUTIC modules make the above described settings.
0%
7 (output: 5 ... 8)
0%
Light module
0%
Order No. 2381
0%
offset
8 (output: 5 ... 8)
Soundswitch
Order No. 2382
The figure shows an example of the connectivity of the " 2-16 C NAUTIC
Expert Switch building block ", " 1/4 K NAUTIC Multi-Prop Mini-Decoder ",
" light module " and " sound switch ". Two of these modules in parallel can
be operated using the menu »Multi channel« on output 5 ... 8.
Note:
Due to technical reasons, servos connected
to a 1/4 C NAUTIC Multi-Prop mini decoder
may operate somewhat hesitatingly. This is
not a fault.
Connection notes for the
Nautic-Expert switching module, No. 4159
As many as 16 switched functions can be controlled
per switching module.
Eight loads, like lamps, LEDs, etc. – but not electric mo-
tors – , with a load current of up to 0.7 A each can be
(Receiver power supply to the „B + -"
marked terminals)
additional servos, speed controller,
sail winch, ... also on this side
Empfänger
Batt. 3...30V
Best.-Nr. 4159 1- H -2
2 - 16 K
1- G -2
1- F -2
1- E -2
NAUTI C - Expert
1- D -2
Schaltbaustein
1- C -2
1- B -2
1- A -2
M
connected directly.
Two switch functions per connector socket are pos-
sible via the three conductor cable, No. 3941.6 , see
bottom right figure.
Electric motors and loads drawing substantial current
should be connected by other means, e. g. via switch-
ing modules. Ask your dealer about this.
6 (output: 5 ... 8)
RX
Best.-Nr. 4142.N
1/4 K NAUTIC
S 4
S 3
Multi-Prop-
S 2
Mini-Decoder
S 1
Switching module
Switching
high voltage
module
SXH Order No. 3970
SXH
Switching module
Switching
multi function
module
SXM Order No. 3971
SXM
external power-
supply 3 ... 30 V
+
-
- +
additional modules e.g. ...
Switching module high voltage SXH Order No. 3970
Switching module multi function SXM Order No. 3971
Wiring for direct connection of two consumer units at one output
3-pole cable with flat connector Order No. 3941.6
consumer
Current consumption of directly
brown
unit
max. 0,7 A connected consumer units
(but no electric motors)
consumer
unit
max. 0,7 A (total max. 8 x 0,7 A).
orange red max. 0,7 A
Program description - Multichannel 259