Out Convert; Sdi Out; Sdi Level - AJA Ki Pro Ultra Installation & Operation Manual

1.5 OUT CONVERT

1.6 SDI OUT

1.64 3G SDI Level
Ki Pro Ultra v1.2r1
This parameter sets output conversion to one of the available selections. These are the
options:
None (default)
2K Crop to 1080
4K Crop to UltraHD
NOTE: The 4K Crop to UltraHD selection has no impact if a 2K or 1080 video source is used. Also, the
2K Crop to 1080 has no impact if a UltraHD or 1080 video source is used.
When the Ki Pro Ultra uses its factory defaults, the HDMI output video will reflect the
format of the input video, unless the input signal is either a 4K 50Hz or UHD 50Hz signal
and above. In the latter two cases, the video format will either be 2K or 1920 respectively
if downstream the HDMI monitor is not capable of receiving a YCbCr 4:2:0 stream.
Otherwise, the monitor will receive the full resolution of the video format, except that the
YCbCr signal will be 4:2:0 instead of 4:2:2. The HDMI Out and HDMI/EDID Override menus
allows the user to change the video format and the chroma resolution when the
downstream HDMI monitor does not transmit its EDID, or capabilities, correctly.
The SDI Monitor output, on the other hand, will always decimate the frame size when the
input source is either UHD or 4K. Additionally, the user may select the Monitor Output's
Out Convert option, which will mirror the selection made in the Out Convert menu, 1.5.
In other words, if the input format is 2K, the user can choose "2K Crop to 1080" option in
menu 1.5 and the "Out Convert" option in menu 1.8 to yield a 1080 output for
downstream monitors that cannot accept a 2K signal.
This parameter sets the SDI output format.These are the options:
SDI 1 RGB
SDI 1 YCbCr
SDI 1-2 RGB
SDI 1-2 YCbCr
SDI 1-4 RGB (default)
SDI 1-4 YCbCr
NOTE: SDI 1 RGB and SDI 1 YCbCr high frame rates (in excess of 29.97fps) are supported by 3G-SDI.
Be sure to connect the AJA Ki Pro Ultra to a 3G-SDI capable device in these cases. If a 3G-SDI
capable device is not available, RGB and high frame rate YCbCr may be output via SDI 1 and
SDI 2 as "dual link" 1.485Gbps."
This parameter allows the 3G SDI output to be configured for either Level A or Level B.
While many 3G SDI devices will support both Level A and Level B, some devices may
need a specific 3G SDI selection to operate as expected.
Level B (default)
Level A
The output is not converted
Converts and crops 2K output to 1080 HD
Converts and crops 4K output to UltraHD
Sets SDI 1 to RGB (supports up to 2K 29.97fps)
Sets SDI 1 to YCbCr (supports up to 2K 59.94fps)
Sets SDI 1-2 outputs to RGB (supports up to 2K 29.97fps)
Sets SDI 1-2 outputs to YCbCr (supports up to 2K 59.94fps)
Sets SDI 1-4 outputs to RGB (supports up to 4K 29.97fps)
Sets SDI 1-4 outputs to YCbCr (supports up to 4K 59.94fps)
For use with devices that accept or require Level B.
For use with devices that accept or require Level A.
47
www.aja.com