MIMAKI UJF-3042 Maintenance Manual page 220

Maintenance Manual > Troubleshooting > Details on Errors and Malfunctions > List of SYSTEM HALT
Model UJF-3042/FX Issued 2010.08.27 Revised 2011.09.30 F/W ver
7.1.4 List of SYSTEM HALT
 List of SYSTEM HALT (7/7)
No. LCD
FW error
SYSTEM HALT (*)
62
(Wiper operation range error)
813 : FW/WIPER RN
FW error
SYSTEM HALT (*)
63
(drivinfm() information obtaining error
814 : FW/drivinfm
FW error
SYSTEM HALT (*)
64
(Serial control F/W error (material control))
815 : FW/SIO rsrc
FW error
SYSTEM HALT (*)
65
(FROM write control error)
816 : FW/FROM WRC
FW error
SYSTEM HALT (*)
66
(Save area error (size over))
817 : FW/SaveArea
FW error
SYSTEM HALT (*)
67
(EEPROM size over)
818 : FW/EEP SIZE
FW error
SYSTEM HALT (*)
68
(HDROM size over)
819 : FW/HROM SIZ
FW error
SYSTEM HALT (*)
69
(FROM size over)
81a : FW/FROM SIZ
FW error
SYSTEM HALT (*)
70
(STACK OVER)
81b : FW/STACK OV
System error
SYSTEM HALT (*)
(STC3 A/D start error)
000 : IOC1/ADC
71
System error
SYSTEM HALT (*)
(SPC A/D start error)
000 : IOC2/ADC
72
System error
SYSTEM HALT (*)
(HDC A/D start error)
000 : HDC/ADC
73
Unnown error
SYSTEM HALT (*)
000 : UNNOWN ERR
74
© 2013 MIMAKI ENGINEERING CO.,LTD.
1.80 / 1.00
Cause
1. Update F/W.
2. Check and clear the parameter.
3. Disconnect and connect the FFC located between the
Main PCB and the SL-Relay PCB.
4. Disconnect and connect the FFC located between the
Main PCB and the Station III PCB.
5. Disconnect and connect the FFC located between the
SL-Relay PCB and the Slider PCB.
6. Replace the FFC located between the Main PCB and
the SL-Relay PCB.
7. Replace the FFC located between the Main PCB and
the Station III PCB.
8. Replace the FFC located between the SL-Relay PCB
and the Slider PCB.
9. Replace the Main PCB with a new one.
1. Confirm the neighboring temperature of the Station III
PCB. In addition, confirm whether and it is an error by
the heat reckless driving of FPGA.
2. Confirm whether there is not a device generating
powerful electromagnetic waves to circumference.
3. Replace the Slider PCB with a new one.
6.4.5)
4. Replace the Main PCB with a new one.
5. Replace the Power Supply PCB with a new one.
(Refer to 6.4.1)
1. Confirm the neighboring temperature of the SL-Relay
PCB. In addition, confirm whether and it is an error by
the heat reckless driving of FPGA.
2. Confirm whether there is not a device generating
powerful electromagnetic waves to circumference.
3. Replace the Slider PCB with a new one.
6.4.5)
4. Replace the Main PCB with a new one.
5. Replace the Power Supply PCB with a new one.
(Refer to 6.4.1)
1. Confirm the neighboring temperature of the Slider
PCB. In addition, confirm whether and it is an error by
the heat reckless driving of FPGA.
2. Confirm whether there is not a device generating
powerful electromagnetic waves to circumference.
3. Replace the Slider PCB with a new one.
6.4.5)
4. Replace the Main PCB with a new one.
5. Replace the Power Supply PCB with a new one.
(Refer to 6.4.1)
1. Update F/W.
2. Check and clear the parameter.
3. Replace the Main PCB with a new one.
Remark
Corrective Measures
(Refer to 3.3.1)
(Refer to
(Refer to 3.3.1)
(Refer to
(Refer to 3.3.1)
(Refer to
(Refer to 3.3.1)
(Refer to 3.3.1)
7.1.4
Rev.
2.0
1
2
3
4
5
6
7
8
R.2.0 P.7