Sony PDW-HR1 Operation Manual page 158

Item number Item name
802 DIGITAL AUDIO MUTING IN
SHUTTLE MODE
807 AUDIO OUTPUT PHASE
808 INTERNAL AUDIO SIGNAL
GENERATOR
820 AUDIO OUTPUT CH3/CH4 SELECT Select the signals output from the ANALOG AUDIO OUTPUT 3 and 4
823 NON-AUDIO FLAG PB
Sub-item
1 CH1/CH2
2 CH3/CH4
3 CH5/CH6
4 CH7/CH8
824 ANALOG LINE OUTPUT SELECT
Sub-item
1 CH1/CH2
2 CH3/CH4
828 SDI AUDIO OUTPUT SELECT
Sub-item
1 CH1/CH2
2 CH3/CH4
158
Setup Menu
Menu items in the 800s, relating to audio control (AUDIO CONTROL)
Settings
Set the audio muting conditions during shuttle playback.
off: Not muted.
on: Muted.
Set the output timing of digital audio playback signals (HDSDI, SDI only),
with 80H as a reference position. Output timing is earlier for values
smaller than 80H and later for values greater than 80H. (80H, 128
samples = approx. 2.7 ms, 80H, 1 sample = approx. 20 μs)
0 (0 (HEX)) to 80 (80 (HEX)) to FF (FF (HEX)): Values can be set in this
Select the operation of the internal audio test signal generator.
off: Prevent "SG" from being selected for sub-item AU INPUT of items
silnc (silence): Silent signal.
1kHz (1kHz sine): 1 kHz, –20 dB FS sine wave signal.
When you set the AU INPUT item on page P2 AUDIO of the function
menu to "SG", the internal signal generator operates and outputs
simultaneous test signals to channels 1 to 8 (see page 58).
connectors.
line (line out): Output the signals of the audio channels selected with
moni (monitor out): Output the left channel of the monitor audio (CH-1)
Control non-audio flags in digital audio output.
During playback (except E-E mode), set non-audio flags in digital audio
output to the following states.
on: Set to on (data is non-audio.)
auto: Set as follows.
Select the analog audio signals (tracks 1 to 8) to be assigned to audio
output channels.
tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.
Select the audio signals to assign to SDI audio output channels.
tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.
range.
A1 INPUT to A8 INPUT on the P2 AUDIO page of the function
menu.
item 824 from the ANALOG AUDIO OUTPUT 3 and 4 connectors.
from the ANALOG AUDIO OUTPUT 3 connector, and output the
right channel (CH-2) from the ANALOG AUDIO OUTPUT 4
connector.
• When data is read from disc and confirmed: Follow the data.
• When data from disc is not confirmed: Maintain current state.