Sony PDW-HR1 Operation Manual page 156

Item number Item name
713 VIDEO SETUP REFERENCE
Sub-item
INPUT LEVEL 59.94i/59.94P/
OUTPUT
LEVEL
715 VIDEO GAIN CONTROL
716 CHROMA GAIN CONTROL
717 CHROMA PHASE CONTROL
718 SETUP LEVEL (59.94i/59.94P/
29.97P mode)/BLACK LEVEL (50i/
50P/25P mode)
719 SYSTEM PHASE SYNC
720 SYSTEM PHASE SC
723 INPUT VIDEO BLANK
Sub-item
1
2...10 LINE 12
2...15 LINE 9
726 H BLANKING WIDTH
728 OUTPUT SCH PHASE
156
Setup Menu
Menu items in the 700s, relating to video control (VIDEO CONTROL)
29.97P mode (UC)
59.94i/59.94P/
29.97P mode (J)
In 59.94i/59.94P/
29.97P mode (UC)
In 59.94i/59.94P/
29.97P mode (J)
ALL LINE
In 59.94i/59.94P/
... 29.97P
LINE 20 mode
In 50i/50P/25P
... mode
LINE 22
Settings
Set the video setup amount to be added to the composite input and
output signal (in 59.94i/59.94P/29.97P mode only).
Remove the setup level selected by this item frrom the input signal.
0.0%, 7.5%
Remove the setup level selected by this item frrom the input signal.
0.0%, 7.5%
Add the setup level selected by this item to the output signal.
0.0%, 7.5%
Add the setup level selected by this item to the output signal.
0.0%, 7.5%
Adjust the video output level.
–2048 (–2048 (DEC)) to 0 (0 (DEC)) to 848 (848 (DEC))
Adjust the chroma output level.
–2048 (–2048 (DEC)) to 0 (0 (DEC)) to 848 (848 (DEC))
Adjust the chroma phase.
–128 (–128 (DEC)) to 0 (0 (DEC)) to 127 (127 (DEC))
Adjust the setup level (black level).
–272 (–272 (DEC)) to 0 (0 (DEC)) to 272 (272 (DEC))
Adjust the output signal sync phase.
–128 (–128 (DEC)) to 0 (0 (DEC)) to 127 (127 (DEC))
Adjust the output signal subcarrier phase.
0 (0 (DEC)) to 511 (511 (DEC))
Switch blanking on or off for lines in the vertical blanking interval of input
video signals. Lines can be specified individually. Y/C signals and odd/
even fields are blanked simultaneously.
Blanking in recorded signals is carried out according to these settings.
- - -: Specify the blanking for each line separately.
blnk: Regardless of the settings of other sub-items, blank all lines which
can be specified in this menu item.
thru: Regardless of the settings of other sub-items, switch blanking off for
all lines which can be specified in this menu item.
Specify blanking for lines 12 to 20.
blnk: Switch blanking on.
thru: Switch blanking off.
Specify blanking for lines 9, 322 to 22, and 335.
blnk: Switch blanking on.
thru: Switch blanking off.
Select the horizontal blanking width of the output analog video signal.
narow (narrow): Digital blanking (narrow)
wide: Analog blanking (wide)
When "wide" is selected, the horizontal blanking width complies with
SMPTE-170M, and normally the blanking is widened and the image
becomes narrower. It is recommended to select "narow" at the editing
stage, then later, for broadcast transmission to select "wide", to output a
signal conforming to the standard. Note, however, that "narow" has to be
always selected for SDI signals.
Set the subcarrier H phase.
–512 (–512 (DEC)) to 0 (0 (DEC)) to 511 (511 (DEC))