General Maintenance; Installing Reel Easy Line Trimmer Head; Installing Line In Reel Easy Line Trimmer Head; Iinstalling Pro Cut Ii Line Trimmer Head - Ryobi RLT430CES Operator's Manual

EN
FR DE ES
dusty, also wear a dust mask.
WARNING:
Before inspecting, cleaning, or servicing the
machine, shut off engine, wait for all moving parts
to stop, and disconnect spark plug wire and move
it away from spark plug. Failure to follow these
instructions can result in serious personal injury or
property damage.
GENERAL MAINTENA
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, lubricant, grease,
etc.
WARNING:
Do not at any time let brake fluids, petrol,
petroleum-based products, penetrating lubricants,
etc., come in contact with plastic parts. Chemicals
can damage, weaken or destroy plastic which may
result in serious personal injury.
You can often make adjustments and repairs described
here. For other repairs, have the trimmer serviced by an
authorised service dealer.

INSTALLING REEL EASY LINE TRIMMER HEAD

See Figures 5.
Stop the engine and disconnect the spark plug wire.
Q
Remove currently installed line trimmer head.
Q
Open the Reel Easy Line Trimmer Head by
Q
depressing the latches on each side. The contents
of the line trimmer head are spring loaded, so keep
your other hand over the line trimmer head cover
while depressing the latches.
Remove the line trimmer head cover, knob, and
Q
spool and set aside.
Place the line trimmer head on the drive shaft. Make
Q
sure the line trimmer head is fully seated.
Install the hex bolt into the opening on the drive shaft
Q
and secure using the hex-shaped opening in the
knob to tighten.
NOTE: Only use the knob to tighten the bolt. The
use of other tools may allow over tightening of the
bolt, which could damage the line trimmer head.
If removed, replace the spring into the line trimmer
Q
head and push down to seat.
Reinstall the spool. For the RLT430CES curved line
Q
trimmer attachment, the spool should be placed so
"This side out for curved shaft" is visible. If you are
using a straight shaft attachment with the Reel Easy
cutting head the spool should be placed so "This
IT PT NL SV DA
English (original instructions)
NO FI HU CS RU
side out for straight shaft" is visible.
Q Replace the knob in the spool.
Replace the line trimmer head cover, aligning latches
Q
with openings in the line trimmer head. Press cover
and line trimmer head together until both latches
snap into openings securely.
Q Install line as described in the next section of this
manual.
INSTALLING LINE IN REEL EASY LINE TRIMMER
HEAD See Figures 5.
Use 2.4mm diameter monofilament line.
Stop the engine and disconnect the spark plug wire.
Q
Cut one piece of line approximately 7.5 meters in
Q
length.
Rotate knob on line trimmer head until line on knob
Q
aligns with arrows on top of line trimmer head.
Insert one end of line into eyelet located on the side
Q
of the line trimmer head and push until line comes
out through the eyelet on the other side. Continue
to push line through the line trimmer head until the
middle section of the line is inside the line trimmer
head and line outside the line trimmer head is evenly
divided on each side.
Rotate the knob on the line trimmer head to wind
Q
the line. If using the RLT430CES curved shaft line
trimmer attachment, the knob should be rotated
clockwise. If using a straight shaft attachment, the,
knob should be rotated counterclockwise. Wind the
line until approximately 20 cm remains protruding
from the line trimmer head.

IINSTALLING PRO CUT II LINE TRIMMER HEAD

See Figure 20.
Stop the engine and disconnect the spark plug wire.
Q
Remove currently installed line head.
Q
Install the line head on the drive shaft until fully
Q
seated.
Install the spool retainer and turn clockwise for
Q
curved shaft attachments (RLT430CES line trimmer
attachment) or counterclockwise for straight shaft
attachments to secure.
Install line as described in the next section of this
Q
manual.
INSTALLING LINE IN PRO CUT II LINE HEAD
See Figure 9.
Use monofilament line between 2.4mm and 2.6mm
diameter. Use quality monofilament replacement line for
best performance.
Q Stop the engine and disconnect the spark plug wire.
Gather two of the pre-cut lengths of trimmer line
Q
provided or cut two pieces of trimmer line, in 27cm.
lengths.
21
RO PL SL HR ET LT LV SK BG