Table of Contents
Advertisement
Page Commands (Cont.)
@PPG
Toggle a specific popup page on either a specified page or the current page. If the page name is empty, the current page is used
(see example 2). Toggling refers to the activating/deactivating (On/Off) of a popup page. This command works in the same way
as the 'Toggle Popup' command in TPDesign4.
Syntax:
Variable:
Example:
Example 2:
@PPK
Kill refers to the deactivating (Off) of a popup window from all pages. If the pop-up page is part of a group, the whole group is
deactivated. This command works in the same way as the 'Clear Group' command in TPDesign 4.
Syntax:
Variable:
Example:
@PPM
Set the modality of a specific popup page to Modal or NonModal.
A Modal popup page, when active, only allows you to use the buttons and features on that popup page. All other buttons on the
panel page are inactivated.
Syntax:
Variable:
Example:
@PPN
Activate a specific popup page to launch on either a specified page or the current page. If the page name is empty, the current
page is used (see example 2). If the popup page is already on, do not re-draw it. This command works in the same way as the
'Show Popup' command in TPDesign4.
Syntax:
Variable:
Example:
Example 2:
@PPT
Set a specific popup page to timeout within a specified time. If timeout is empty, popup page will clear the timeout.
Syntax:
Variable:
Example:
MVP-5200i Modero® ViewPoint® Touch Panel with Intercom - Instruction Manual
"'@PPG-<popup page name>;<page name>'"
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
SEND_COMMAND Panel,"'@PPG-Popup1;Main'"
Toggles the popup page 'Popup1' on the 'Main' page from one state to another (On/Off).
SEND_COMMAND Panel,"'@PPG-Popup1'"
Toggles the popup page 'Popup1' on the current page from one state to another (On/Off).
"'@PPK-<popup page name>'"
popup page name = 1 - 50 ASCII characters. Name of the popup page.
SEND_COMMAND Panel,"'@PPK-Popup1'"
Kills the popup page 'Popup1' on all pages.
"'@PPM-<popup page name>;<mode>'"
popup page name = 1 - 50 ASCII characters. Name of the popup page.
mode =
NONMODAL converts a previously Modal popup page to a NonModal.
MODAL converts a previously NonModal popup page to Modal.
modal = 1 and non-modal = 0
SEND_COMMAND Panel,"'@PPM-Popup1;Modal'"
Sets the popup page 'Popup1' to Modal.
SEND_COMMAND Panel,"'@PPM-Popup1;1'"
Sets the popup page 'Popup1' to Modal.
"'@PPN-<popup page name>;<page name>'"
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
SEND_COMMAND Panel,"'@PPN-Popup1;Main'"
Activates 'Popup1' on the 'Main' page.
SEND_COMMAND Panel,"'@PPN-Popup1'"
Activates the popup page 'Popup1' on the current page.
"'@PPT-<popup page name>;<timeout>'"
popup page name = 1 - 50 ASCII characters. Name of the popup page.
timeout = Timeout duration in 1/10ths of a second.
SEND_COMMAND Panel,"'@PPT-Popup1;30'"
Sets the popup page 'Popup1' to timeout within 3 seconds.
Programming
83
Advertisement
Table of Contents
