Worth Data TriCoder t53 User Manual page 150

DATA TOO SHORT
HIT ANY KEY_
DATA TYPE ERROR
HIT ANY KEY_
DATA UPLOAD?
KEY [YES/NO]?_
DATA XMIT ERROR
CYCLE POWER
DELETE PROGRAM?
KEY [YES/NO]?_
Downloading Firmware
Please Wait
DUPLICATE ACCESS
HIT ANY KEY_
EDIT PROGRAM?
KEY [YES/NO]?_
END OF FILE
HIT ANY KEY_
END OF PGM RECV.
HIT ANY KEY_
END OF PGM XMIT
HIT ANY KEY_
END OF TRANSMIT
DEL FILE [Y/N]?_
ENTRY TYPE ERROR
HIT ANY KEY_
EOT, FILE ERASED
HIT ANY KEY_
EOT, FILE SAVED
HIT ANY KEY_
FATAL ENTRY TYPE
CYCLE POWER_
FATAL EXEC CALL
831-458-9938 NOW_
FATAL STMT #.
CYCLE POWER_
FILE NOT DEFINED
HIT ANY KEY_
FILE USED BY Pn
HIT ANY KEY_
Firmware Download
Via Serial Port?
Firmware Download
Via USB Port?
Too few characters were entered.
Alphabetic character entered when
numeric is expected or vice versa.
Do you want to upload data?
Data transmission error on upload
or other data transmission.
Upon entering Programming Mode,
you selected a program and
answered NO to EDIT PGM? Do
you want to delete?
Firmware Download has started.
In a table where you have specified
NO DUPLICATE ACCESS you
have accessed a record twice.
In Programming Mode, do you
want to edit a program? You can
edit program #1,#2 or #3.
You are at the end of a data file or
a program file.
You have finished receiving a
program from another TriCoder or
a host computer.
You have successfully transmitted
a program to a host computer or
another TriCoder.
A data file has been successfully
uploaded. Do you want to delete
the file?
In Programming Mode, you have
entered a character other than
DQTYSX at the ENTRY TYPE
prompt.
During modem data transfer, End
of Transmission occurred and data
file was erased.
During modem data transfer, End
of Transmission occurred and data
file was saved.
An invalid Entry Type has been
detected in your program. Cycle
power , see what happens.
Something is definitely wrong.
Cycle power, see what happens.
An invalid Statement Number was
detected. Cycle Power and see
what happens.
You have selected a data file # that
has not been defined in the
PARTITIONS setup parameter.
You have selected a data file # with
data in it, collected by another
program. n=1-3. Select another
data file #.
Appears at Fail-Safe download or
normal download with serial
Computer Interface specified.
Firmware download has been
requested with wedge Computer
Interface or user has serial
Computer Interface and has said
NO to "serial firmware download?"
14-2
Enter more characters or
decrease your Minimum
Character Length.
Re-enter data or change
Data Type in program.
Press YES or NO.
Turn TriCoder off then
restart
Press YES to delete
program. Press NO to go
back to menu.
Wait 1.5 minutes for serial.
Wait 0.1 minutes for USB.
HIT ANY KEY. Enter a
different piece of data.
Press YES or NO.
Press any key to see last
record.
Press any key to go to the
Mode Menu.
Press any key to go to the
Mode Menu.
Press YES to delete the file
Press NO to keep the file.
HIT ANY KEY and re-enter
character.
HIT ANY KEY to go to
Mode Menu
HIT ANY KEY to go to
Mode Menu
Turn TriCoder OFF/On. Call
for support if bad.
Turn TriCoder OFF/ON. Call
for support if bad.
Turn TriCoder OFF/ON. Call
for support if bad.
HIT ANY KEY. Go to Setup
and set PARTIONS.
HIT ANY KEY. Select
another data file #.
Yes proceeds to download.
No exits to Mode Menu or
asks about USB download.
Yes proceeds to firmware
download. No exits to Mode
Menu.