Canon iR3570 Service Manual page 607

Cause
When the machine is started up, its IP address is not
assigned by means of DHCP, RARP, or BOOTP.
# 756
In system control setup (user mode), 'use NetWare' is set
to 'off' in NetWare settings.
# 801
While e-mail is being transmitted or i-fax is transmitted/
received, the communication with the SMTP server
encountered a timeout error because of a factor
associated with the main server.
While an SMTP connection is being used, the SMTP
server has returned an error.
The address setting is not correct.
When data is transmitted to the file server, an error has
occurred owing to a factor associated with the server.
An attempt has been made to transmit data to an address
not authorized for a write operation.
In the course of transmitting data (file server), it was
found that there is a file having the same name, and an
overwrite operation to the file is prohibited.
In relation to transmission (file server), the folder name
or the password that has been specified is wrong.
# 802
In the system control setup (user mode), the settings of
the SMTP server for e-mail/i-fax are wrong.
The setting of the DNS server is wrong.
The attempt to connect to the DNS server has failed.
# 803
Before all pages have been transmitted, the target has cut
off the network.
# 804
When an attempt is made to transmit to the file server, it
has been found that no match exits in the specified
directory.
You are not authorized for access to the folder.
# 806
When an attempt to transmit to the file server is made, it
has been found that the specified user name or password
is wrong.
The address specified for e-mail/i-fax transmission is
wrong.
# 810
When an attempt is made to receive i-fax, a POP server
connection error has occurred.
While a connection is made to the POP server, an error
has been returned by the POP server.
While a connection is made to the POP server, a timeout
error has occurred owing to a factor associated with the
server.
# 815
If a file that has been transmitted to the file server is
being printed, you will not be able to log in to the server
in question.
# 818
The data that has been received is in a format that does
not permit printing.
# 819
The data that has been received is of a type that cannot
be handled (i.e., its MIME information is illegal).
# 820
The data that has been received is of a type that cannot
be handled (i.e., BASE64 or Unicode is illegal).
# 821
The data that has been received is of a type that cannot
be handled (i.e., TIFF interpretation error has occurred).
# 822
The data that has been received is of a type that cannot
be handled (i.e., the image cannot be decoded).
# 827
The data that has been received is of a type that cannot
be handed (i.e., part of its MIME information is not
supported).
# 828
Remedy
In user mode, check the TCP/IP settings.
In network settings of system control setup (user mode),
set 'use NetWare' to 'on'.
1. Check to see that SMTP is operating normally.
2. Check the condition of the network.
1. Check to see if SMTP is operating normally.
2. Check the condition of the network.
3. Check the address setting.
4. Check the condition of the file server and the setting.
Check the address setting.
Change the setting of the file server so that overwriting
may be permitted.
Check the address setting.
In the network settings under system control settings
(user mode), check the SMTP server name and the DNS
server name. Check to see if the DNS server is operating
normally.
Try once again.
Check the address.
Set the server so that you will be authorized to access the
folder.
Change the user name or the password of the address.
Check the address of the e-mail/i-fax in question.
1. In user mode, check the POP server name setting.
2. Check the operation of the POP server.
3. Check the condition of the network.
1. In user mode, check the POP server name setting.
2. Check the operation of the POP server.
3. Check the condition of the network.
1. In user mode, check the POP server name setting.
2. Check the operation of the POP server.
3. Check the condition of the network.
Wait a while, and then try once again. Or, change the
NetWare server settings of the target, or stop PServer.
Ask the source to change the file format and transmit it
once again.
Ask the target to check the settings and transmit it once
again.
Ask the source to check the settings and transmit it once
again.
Ask the target to check the settings and transmit once
again.
Ask the source to check the settings and transmit once
again.
Ask the source to check the settings and transmit once
again.
Chapter 15
15-19