E602 In Detaill - Canon iR3570 Service Manual

E740
E743
E744
E745
E746
E748
E805

15.2.2 E602 in Detaill

iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N / / iR4570N / iR2230 / /
XX YY Description
00
00
Code Cause
There is an error on the Ether board.
0002 The MAC address is illegal.
There is an error in the DDI communication.
0000 An SCI error has occurred. The received data is
faulty. A reception timeout condition has
occurred. An SEQ timeout error has occurred.
There is an error in the language file/boot ROM.
0001 The version of the language file on the HDD and
that of the bootable do not match.
0002 The size of the language file on the HDD is too
large.
0003 There is no language file on the HDD indicated
by config.txt for a switchover.
0004 An attempt to switchover to a language on the
HDD fails.
1000 The boot ROM that is mounted is of the wrong
type.
2000 The engine ID indicated by the software ID is
illegal.
3xxx Disagreement between the installed memory and
the boot ROM
There is a fault on the TokeRing board.
0001 An attempt at PCI initialization has failed.
0002 The MAC address is faulty.
0003 There is an error in the acquisition/setting of
board information.
0004 There is a connection error.
0005 Other Errors
The accessories board is of the wrong type.
0003 At startup, a board for a different model has been
detected.
There is a mismatch between controller board and SDRAM size.
1001 There is a mismatch between the control board
and the SDRAM.
There is a fan error.
0000 While the fan is at rest, the lock signal has been
detected for 5 sec.
While the fan is in operation, the lock signal is not
detected for 5 sec.
01 The HDD cannot be recognized. The
startup partition (BOOTDEV) cannot be
found at startup.
02 The system software for the main CPU
does not exist.
Remedy
Replace the LAN card.
Disconnect and then connect the flexible cable used
to connect the reader unit and the printer unit.
Replace the following as necessary: flexible cable,
reader controller PCB, main controller PCB.
Download a language file of the correct version.
Download a language file of the correct version.
Download a language file of the correct version.
Download a language file of the correct version.
Replace the boot ROM with one of the model in
question.
Replace it with a software ID of the correct model.
Confirm and correct the installed memory and the
boot ROM.
1. Disconnect and then connect the TokeRing board.
2. Replace the TokeRing board.
1. Replace the TokenRing board.
1. Replace the TokenRing board.
1. Check the connection of the cable.
2. Replace the cable.
3. Check the power source of the MAU.
4. Replace the MAU.
5. Replace the TokenRing board.
Replace the UFR board of the correct type (model).
Check the correct combination between board and
SDRAM.
Replace the fan. Replace the DC controller PCB.
T-15-3
Remedy
1. Turn off the main switch, and check the cable connector.
Then, turn on the main switch.
2. Check to see if the HDD spins up when the main switch
is turned on and if the 5V/12V power is supplied.
3. If the symptom still exists after the foregoing, replace
the HDD, re-install the system software. If the symptom
still exists, replace the main board.
1. Start up in safe mode, and format the HDD using the
SST (all); then, re-initial the system software (System,
Language, RUI); then turn off and then back on the main
power switch.
2. If the symptom still exists after the foregoing, suspect a
fault on the HDD, and replace the HDD and re-install the
system software.
Chapter 15
0008-1182
15-7