Kyocera KM-C2525E Service Manual page 158

2JL/2JJ/2JG/2JD-1
(5) Printer settings
Print status page
Print a status page to check details such as current set-
tings, available memory, and installed optional equip-
ment.
1. Press [Print Status Page].
2. Press [Printing].
3. The status page is printed.
Parallel interface mode configuration
For normal usage, leave the default setting as [Auto].
Use a parallel interface cable compliant with the
IEEE1284 specification.
1. Press [Interface].
2. Press [Parallel] and press [Change #].
3. Select the desired mode.
Auto/Normal/High Speed/Nibble (High)
4. Press [Close].
Serial interface mode configuration
Configure the baud rate (communication speed), data
big, stop bit, parity, and protocol to be used by the serial
interface.
1. Press [Interface].
2. Press [Serial].
3. Select [Baud Rate] using the cursor up/down keys
and press [Change #].
4. Select [1200], [2400], [4800], [9600], [19200],
[38400], [57600] or [115200].
5. Press [Close].
6. Refer to steps 3 - 5 to configure data bit, stop bit,
parity and protocol.
Data bit: Select [7] or [8].
Stop bit: Select [1] or [2].
Parity: Select [None], [Odd], [Even] or [Ignore].
Protocol: Select [DTR (positive) &XOn/Xoff], [DTR
(positive)], [DTR (negative)], [XOn/Xoff] or [ETX/
ACK].
7. Press [Close].
TCP/IP settings
To connect to a Windows network via TCP/IP, set to [On].
Continue to set DHCP, BOOTP, IP address, subnet mask
address, and gateway address.
1. Press [Interface].
2. Press [Network].
To set the optional network interface, press
[Option].
3. Select [TCP/IP] using the cursor up/down keys and
press [Change #].
4. Press [On].
5. Select [DHCP] using the cursor up/down keys and
press [Change #].
6. Press [On] or [Off] and press [Close].
7. Select [BOOTP] using the cursor up/down keys and
press [Change #].
8. Press [On] or [Off] and press [Close].
9. Select [IP Address] using the cursor up/down keys
and press [Change #].
1-3-118
10. Enter the IP address using the numeric keys. Input
the address for the 3 digits displayed in reverse
black and white and press the [#] key.
11. Input the address for the next 3 digits displayed in
reverse black and white and press the [#] key.
To correct an address entry, press the [#] key to
select the 3 digit address you would like to correct
and reenter the address using the numeric keys.
12. After inputting the rest of the address in the same
manner, press [Close].
13. Refer to steps 9 - 12 to set subnet mask address
and gateway address.
14. Press [Close].
Netware setting
To connect via the Netware protocol, set to [On] and set
frame mode.
1. Press [Interface].
2. Press [Network].
To set the optional network interface, press
[Option].
3. Select [NetWare] using the cursor up/down keys
and press [Change #].
4. Select [On] or [Off].
When [On] is selected, select the frame type.
Auto/802.3/Ethernet II/802.2/802.3SNAP
5. Press [Close].
Ethertalk setting
Set EtherTalk to [On] to connect this device to an Apple
Macintosh computer.
1. Press [Interface].
2. Press [Network].
To set the optional network interface, press
[Option].
3. Select [Ethertalk] using the cursor up/down keys
and press [Change #].
4. Select [On] or [Off].
5. Press [Close].
Network status page
The network status page can be printed when printing the
status page. Use the network status page to verify the
network interface firmware version, network address and
network protocol information.
1. Press [Interface].
2. Press [Network].
To set the optional network interface, press
[Option].
3. Select [Network Status Page] using the cursor up/
down keys and press [Change #].
4. Select [On] or [Off].
5. Press [Close].