SATO CL4NX Programming Reference Manual page 337

Name of Setting
Setting value
item
ADJUSTPITCH 609dpi:"-90" to "90" (dot)
305dpi:"-45" to "45" (dot)
203dpi:"-30" to "30" (dot)
ADJUSTOFFSET 609dpi:"-90" to "90" (dot)
305dpi:"-45" to "45" (dot)
203dpi:"-30" to "30" (dot)
OPTIONTIME "0", "5" to "200" (x100ms)
AUTO_MEASURE "0": Disable
"1": Enable
AUTO_ONLINE "0": Disable
"1": Enable
FEED "0": Disable
"1": Enable
ONLINE_FEED "0": Disable
"1": Enable
IGNORE_CRLF "0": Do not remove CR/LF
"1": Remove CR/LF
BYTECOMMAND "0": Disable
"1": Enable
IMLVL_RL "0" to "127": reflective sensor
level(Receiving light)
IMLVL_LE "0" to "7": reflective sensor level
(Light emission)
IM_SL "0.0": Automatic setting
"0.1" to "3.3": Manual setting
GAPLVL_RL "0" to "127": transmissive sensor
level(Receiving light)
GAPLVL_LE "0" to "7": transmissive sensor
level (Light emission)
GAP_SL "0.0": Automatic setting
"0.1" to "3.3": Manual setting
RB_NEND "0": Disable
"1": Enable
PRIORITY "0": Prioritize command
"1": Prioritize LCD setting
PRINT_AREA "0": Normal
"1": Move (3 mm to the back of
thermal head)
ADJUSTDARK "0" to "99"
OP_FEED 609dpi:"0" to "6120" (dot)
305dpi:"0" to "3060" (dot)
203dpi:"0" to "2040" (dot)
PASS_SET "0": Disable
"1": Enable
ALL_QTY "0": Disable
"1": Enable
HEX_DUMP_ "0": Disable
MODE "1": Enable
APP_MODE "00": AUTO
"SB": SBPL
"SZ": SZPL
"SI": SIPL
"SD": SDPL
"ST": STCL
APP_MODE_ "00": AUTO
AUTO "SB": SBPL
"SZ": SZPL
"SI": SIPL
"SD": SDPL
"ST": STCL
CALENDAR_ "0": Disable
CHECK "1": Enable
REPRINT "0": Disable
"1": Enable
initial
Default Vale. R/W
CA
-
0 R/W
-
0 R/W
○
0 R/W
○
0 R/W
○
1 R/W
○
0 R/W
○
0 R/W
○
0 R/W
○
0 R/W
-
95 R/W
-
1 R/W
-
0.0 R/W
-
63 R/W
-
1 R/W
-
0.0 R/W
○
1 R/W
○
0 R/W
○
0 R/W
○
50 R/W
○
0 R/W
-
0 R/W
○
0 R/W
○
0 R/W
-
- R
- R -
○
1 R/W
○
0 R/W
331
Contents of Setting item
Adjust print position
Offset adjust
Waiting time in tear off mode for next
data
<TW>
Automatic measurement of label
length
Auto online
<AO>, <LD>
Initial feed
Online feed
<LF>
Ignore CR/LF
<CL>
Remove CAN/DLE
<1B>
Adjust reflective sensor level
(Receiving light)
Adjust reflective sensor level (Light
emission)
Reflective sensor slice level
Adjust transmissive sensor level
(Receiving light)
Adjust transmissive sensor level
(Light emission)
Transmissive sensor slice level
Detect ribbon near end
Priority setting
Move printable area
Adjust darkness
Optional feed volume
Input password
Display total number of labels to print
HEX DUMP MODE of
Enable/Disable
Application mode
Application mode of AUTO mode
Calendar check
Reprint