Sharp MX-FXX1 Service Manual page 51

SW Bit
Item
No. No.
71 3-4 Image capacity when
receiving
(Reflect in DIS, Do not
reflect in DTC.)
5-6 Designation of
reception size
(indicating the width of
reception capacity)
7-8 Not used
72 1 Report output (when
cancelled)
2 Report output (when
refusing reception)
<FAX only>
3 Printing of transmitted
document contents at
times of F code
communication
<FAX only>
4 Not used
5 Designation of rotation
direction when printing
on both sides and the
rear side.
6 Selection of error page
output when error
occurs during FAX
reception.
7 Selection of re-send
page at times of error
SW selection and function
This sets the reception resolution capacity when FAX calls arrive (when
sending DIS).
Reflect in DIS, Do not reflect in DTC.
"00": Very fine
"01": Fine
"10": When small
"11": Ordinary lettering
This sets this machine's receivable document width that is notified to
the other party's machine when receiving.
"00": By loaded cassette
"01": A4 width
"10": B4 (A4, B4) width
"11": A3 (A3, B4, A4) width
When using the loaded cassette, width is as follows depending on the
maximum cassette size.
A5/5.5x8.5R size: A4 width
B5 size: B4 width
A4/8.5x11 size: A3 width
8.5x13/8.5x14: A3 width
B4 size: B4 width
11x17: B4/A3 width (changeover by means of the FAX soft SW)
A3 size: A3 width
A3 width is adopted in cases where a tray capable of receiving and
printing facsimiles is not set and cases where all cassettes are open.
Setting to determine whether or not to output the communication results
sheet in cases where document transmission is cancelled while in
progress.
"1": Output the communication results sheet.
"0": Do not output the communication results sheet.
Setting to determine whether or not to output the communication results
sheet when reception is refused in FAX reception. However, other than
not printing is set by means of the report output (when receiving)
setting.
"0": Do not output
"1": Output
Internet FAX is set by means of SW155-8.
Irrespective of "Always print" and "Error," the results sheet is not
printed.
Setting to determine whether or not to print part of the transmitted
document on the communication results sheet at times of F code
communication. However, only when the "Document contents printing
at times of transmission" setting is valid.
"0": Do not print
"1": Print
The "Document contents printing (results sheet) at times of
transmission" setting takes priority.
Setting to determine whether to adopt vertical binding or horizontal
binding when printing on both sides.
When horizontal binding is selected, the header position on both sides
(front and rear) is printed in the same direction.
When vertical binding is selected, since the image rotates by 180
degrees, the header position is reversed.
"0": Horizontal binding
"1": Vertical binding
Setting to determine whether to output the error page or to not output it
and discard it in cases where communication errors occur during FAX
reception.
"0": Output the error page
"1": Do not output the error page
However, in cases where errors occur during F code relay-instructed
reception or F code confidential reception, the error page is not
outputted irrespective of this SW setting.
Select the page to be re-sent when errors occur during transmissions
that do not contain F code.
"0": Error page and onwards (re-send from the pages that have not
been transmitted to the other party's machine).
"1": All pages (re-send from the first page including pages that have
been transmitted to the other party's machine).
When transmitting in F code, all pages are re-transmitted irrespective of
this setting.
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 42
Initial value
0 Very fine
0
0 By loaded cassette
0
0
0
0 Do not output
0 Do not output
0 Do not print
0
0 Horizontal binding
0 Output the error page
0 Error page and onwards
System
settings