Sharp MX-FXX1 Service Manual page 17

<Set range and default value of each setup>
Item
FAX send A Image loss
setting OC
B
C
D Image loss
setting SPF
E
SIDE1
F
G Image loss
setting SPF
H
SIDE2
I
SCANNER A Image loss
mode (FAX, setting OC
B
other than
C
COPY)
D Image loss
setting SPF
E
SIDE1
F
G Image loss
setting
H
SPFSIDE2
I
* A to I: The greater the adjustment value is, the greater the image
loss is. 1step=0.1mm
SIMULATION NO.50 27
TEST
SCANNER/FAX-SEND ALL EDGE ADJUSTMENT VALUE
A 30
LEAD_EDGE(OC)
A:
30
B 20 FRONT_REAR(OC)
C 20 TRAIL_EDGE(OC)
0 100
D 30 LEAD_EDGE(SPF_SIDE1)
FAX SCANNER
66
66-1
Purpose : Setting
Function (Purpose) : Used to display the FAX-related soft SW on
the LCD to allow changing the soft SW
while checking with the LCD.
Section : FAX
Item : Setting
Operation/Procedure
1) When the machine enters Simulation 66-01, the screen on the
right is displayed.
2) When [SW NO] is entered with 10-key, "6" is displayed in the
column of [SW NO].
* (In this example, "6" is entered.)
* (The range of value to be entered is 2 to 170.)
* When [C] key is pressed, the entered value of [SW NO] is
cleared.
3) When [DATA] button is pressed, the data of soft SW No. 6 are
displayed.
* When [SW NO] button is pressed, the display returns to the
initial screen.
4) The data of soft SW can be changed with 10-key.
* When 10-key corresponding to the bit is pressed, the bit
data are displayed as follows:
[1] → [0]
[0] → [1]
* When [SW NO] button is pressed, the display returns to the
initial screen.
Display item
LEAD_EDGE (OC) OC lead edge image loss setting
FRONT_REAR (OC) OC side image loss setting
TRAIL_EDGE (OC) OC rear edge image loss setting
LEAD_EDGE (SPF_SIDE1) Front surface lead edge image loss setting
FRONT_REAR (SPF_SIDE1) Front surface side image loss setting
TRAIL_EDGE (SPF_SIDE1) Front surface rear edge image loss setting
LEAD_EDGE (SPF_SIDE2) Back surface lead edge image loss setting
FRONT_REAR (SPF_SIDE2) Back surface side image loss setting
TRAIL_EDGE (SPF_SIDE2) Back surface rear edge image loss setting
LEAD_EDGE(OC) OC lead edge image loss setting
FRONT_REAR(OC) OC side image loss setting
TRAIL_EDGE(OC) OC rear edge image loss setting
LEAD_EDGE(SPF_SIDE1) Front surface lead edge image loss setting
FRONT_REAR(SPF_SIDE1) Front surface side image loss setting
TRAIL_EDGE(SPF_SIDE1) Front surface rear edge image loss setting
LEAD_EDGE(SPF_SIDE2) Back surface lead edge image loss setting
FRONT_REAR(SPF_SIDE2) Back surface side image loss setting
TRAIL_EDGE(SPF_SIDE2) Back surface rear edge image loss setting
0
CLOSE
OK
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 8
Description
5) When [EXECUTE] button is pressed, it is highlighted and the
setting is saved.
After saving the setting, [EXECUTE] button returns to the nor-
mal display.
SIMLATION NO.66-01
TEST
FAX SOFT SW. SETTING.
(SW No.2-170)
SW No.
DATA
1 2 3 4 5 6 7 8
66-2
Purpose : Setting
Function (Purpose) : Used to enter a country code and set the
default value for the country code.
Section : FAX
Item : Setting
Operation/Procedure
1) When the machine enters Simulation 66-02, the following
screen is displayed.
* When [DEST CODE] button is pressed, the display is shifted
to the country code list screen.
* The country code shift screen is shown on the next page.
* The currently set country code is displayed in the column of
"PRESENT:".
2) Enter the country code (8 digits) with 10-key([0]/[1]). The
entered country code is displayed in the column of "NEW:" and
[SET] key becomes active.
* When [C] key is pressed, the column of "NEW:" is cleared.
3) When [SET] button is pressed after entering the country code,
[EXECUTE] button becomes active. The country code is dis-
played in the column of "PRESENT:", and the column of
"NEW:" is cleared.
* When [C] key is pressed, the display returns to the initial set-
ting screen.
4) When [EXECUTE] button is pressed, it is highlighted and
[YES] and [NO] buttons become active. The country name is
displayed on the tile line.
* When [NO] button is pressed, [EXECUTE] button returns to
the normal display and [YES] and [NO] buttons become
inactive.
Set range Default value
0 to 100 30 (3mm)
0 to 100 20 (2mm)
0 to 100 20 (2mm)
0 to 100 20 (2mm)
0 to 100 20 (2mm)
0 to 100 30 (3mm)
0 to 100 20 (2mm)
0 to 100 20 (2mm)
0 to 100 30 (3mm)
0 to 100 0 (0mm)
0 to 100 0 (0mm)
0 to 100 0 (0mm)
0 to 100 0 (0mm)
0 to 100 0 (0mm)
0 to 100 0 (0mm)
0 to 100 0 (0mm)
0 to 100 0 (0mm)
0 to 100 0 (0mm)
CLOSE
EXECUTE