Sharp MX-FXX1 Service Manual page 11

Code
Main Sub
66 11 Used to send the selected signal at 300bps to the line and the speaker. (Send level:
Max.)
12 Used to send the selected signal at 300bps to the line and the speaker. (Send level:
Soft SW setting)
* For the kings of send signals at 300bps, refer to SIM66-11, 300bps send signal table.
13 Used to register dial numbers for SIM66-14/15/16, Dial test. (Up to 20 digits can be
registered.)
14 Used to execute the dial pulse (10PPS) send test and to adjust the make time.
15 Used to execute the dial pulse (20PPS) send test and to adjust the make time.
16 Used to execute the DTFM signal send test and to adjust the send level.
17 Used to send the DTMF signal to the line and the speaker. (Send level: Max.)
18 Used to send the DTMF signal to the line and the speaker. (Send level: Soft SW
setting)
19 Used to write the telephone book data stored in HD into the FLASH ROM.
20 Used to write the telephone book data stored in the FLASH ROM into HD.
21 Used to print the selected items (various registration information, communication
management information, file management information, system error, protocol
monitor).
22 Used to set the handset sound volume. (This simulation can be executed even though
the handset setting is set to NO. When, however, the handset is not installed, the
sound volume cannot be checked.) (Japan model only)
24 Used to clear the FAST save data.
25 Used to register the FAX number for MODEM dial-in.
26 Used to register external telephone numbers for MODEM dial-in.
29 Used to initialize the telephone book data (the one-touch registration table, the FTP/
Desktop expansion table, the group expansion table, the program registration table,
the interface memory box table, the meta data, InboundRouting, and the
DocumentAdmin table).
30 Used to display the TEL/LIU status change, The display is highlighted by status
change.
31 Used to set ON/OFF the port for output to TEL/LIU.
32 Used to check the fixed data received from the line and to display the result.
33 Used to execute detection of various signals with the line connected and to display the
detection result. When a signal is detected, the display is highlighted.
34 Used to execute the send test and display the time required for sending image data in
the test. Used to execute send test and display. (Unit: ms)
36 Used to check send and receive data from the MODEM controller to the MFP controller
or the data line or the command line individually.
39 Used to check and change the destination setting saved in EEPROM of the FAX BOX.
42 Used to rewrite the program to power control installed in the FAX BOX.
43 Used to write the adjustment value into the power control installed in the FAX BOX.
C. Details of simulation
13
13--
Purpose : Clear/cancel (Trouble etc.)
Function (Purpose) : Used to cancel the self-diag "U1" trouble.
Section : FAX
Item : Trouble
Operation/Procedure
1) Press [EXECUTE] button.
2) Press [YES] button to execute cancellation of the trouble.
SIMULATION NO.13
TEST
U1 TROUBLE CANCELLATION
ARE YOU SURE? YES
Function (Purpose)
0
CLOSE
NO
EXECUTE
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 2
Section
Operation test/Check
Operation test/Check
Setting
Adjustment
Adjustment
Adjustment
Operation test/Check
Operation test/Check
Backup
Backup
Check
Setting
Data clear
Setting
Setting
Clear
Operation test/Check
Setting
Operation test/Check
Operation test/Check
Operation test/Check
Operation test/Check
Setting
Setting
Setting
22
22-11
Purpose : Adjustment/Setup/Operation data check
Function (Purpose) : Used to check the use frequency (send/
receive) of FAX.
Section : FAX
Item : Counter
Operation/Procedure
The values of the FAX send counter and the FAX receive counter
are displayed.
Press [COLOR] or [BLACK] button to print.
FAX OUTPUT FAX print quantity counter (for line 1)
FAX OUTPUT_L2 FAX print quantity counter (for line 2)
FAX SEND FAX send counter
FAX RECEIVED FAX receive counter
SEND IMAGES FAX send quantity counter (for line 1)
SEND IMAGES_L2 FAX send quantity counter (for line 2)
SEND TIME FAX send time
RECEIVED TIME FAX receive time
ACR SEND Number of carrier prefix adding communications
Purpose
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
–
FAX