Sharp MX-FXX1 Service Manual page 35

SW Bit
Item
No. No.
22 3 Staple setting
4-5 Staple position setting
6-7 Selection of delivered
sheet size
8 Valid/Invalid setting of
FAX A4, 8.5 x 11
threshold
23 1 Setting for changing
over to automatic
reception during
manual reception
2-6 Setting of the number
of calls for changing
over from manual to
automatic reception
7 Polling protection
8 Switch to sorting in
order of numbers on
the address list
24 1 External telephone off-
hook warning
2-5 Not used
SW selection and function
Set to determine whether or not to staple when outputting received FAX
data.
"0": No
"1": Yes
With the finisher attached, set the staple position for when conducting
stable output of FAX printed data.
"00": Rear 1 point
"01": Front 1 point
"10": Center 2 points
"11": Same action as initial value
The initial value is reverted to if a value outside of the setting range is
set.
Sheet size setting when conducting stable output of FAX/Internet FAX
printed data with the finisher attached.
"00": A4 or A3 (8.5 x 11 or 11 x 17)
"01": B5 or B4 (8.5 x 11 or 8.5 x 14)
"10": A4 (8.5 x 11)
"11": A4R (8.5 x 11R)
When printing received FAX data with A4 and 8.5 x 11 paper in the tray,
this setting determines whether to make threshold values in paper
selection valid or invalid. If made valid, it becomes easier to select
letters.
"0": Valid
"1": Invalid
When printing received Internet FAX data, conduct setting using the
separate SW (Valid/Invalid setting of Internet FAX A4, 8.5 x 11
threshold).
Setting to determine whether or not to initiate automatic reception after
the ringer sounds a certain number of times when manual reception is
set.
"0": Prohibited (do not changeover)
"1": Permitted (changeover)
Set the number of calls before changing over to automatic reception
when in the manual reception mode.
This functions when the "Setting for changing over to automatic
reception during manual reception" (SW23-1) is valid.
Setting can be made over the range of 1 to 32 times by binary inputting.
Set to determine whether or not to execute protection when the other
party requests polling.
"0": Protect
"1": Do not protect
When the protection setting is selected and a request for polling is
received from the other party's machine, bulletin board transmission is
conducted if the source number of the other party coincides with the
number permitted for polling.
When the setting not to protect is selected, bulletin board transmission
is executed regardless of the source number of the other party.
Set to choose between the registered order or the search number order
when neither upward nor downward selection is selected on the
address book screen and address list.
"0": Search number order
"1": Registered number order
This sets whether or not to alarm the external telephone off-hook at the
end of a transmission.
"0": No alarm
"1": Alarm
This switch does not function in North America.
Hand-set always makes the off-hook alarm.
Functions of external telephone depends on TEL/LIU.
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 26
Initial value
0 No Device
setting
0 Rear 1 point Device
setting
0
0 A4 or A3 FAX
(8.5 x 11 or 11 x 17) reception
0
setting
0 Valid
0 Prohibited FAX
reception
setting
0 9 times FAX
reception
1
setting
0
0
0
0 Protect Polling
protection
setting
0 Search number order
0 No alarm (North America/
Australia/New Zealand/
China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle
East/Other3)
1 Alarm (U.K./France/
Germany/Sweden/
Finland/Norway/Denmark/
Netherlands/Italy/
Switcherland/Austria/
Slovakia/Rusia/South
Africa/Spain/Portuguese/
Luxemburg/Belgium/
Czech/Hungary/Greece/
Poland)
1
0
0
0
System
settings