Sharp MX-FXX1 Service Manual page 24

2) Use 10-key to set the handset sound volume. (0: MIN 1:MID-
DLE 2:MAX)
* Enter the sound volume (0 to 2) with 10-key and press [OK]
button. The set sound volume is saved.
* Enter the sound volume (0 to 2) with 10-key and press [EXE-
CUTE] key instead of [OK] key. [EXECUTE] key is high-
lighted and the set sound volume is saved. The on-hold tone
is delivered in the set sound volume.
3) Press [EXECUTE] button to deliver the selected on-hold tone.
* The sound message is outputted to the handset and an
external telephone. The speaker, however, is muted.
* Even during sending the on-hold tone ([EXECUTE] button is
highlighted), the sound volume can be changed by switching
the sound volume button.
* If, however, the handset is not installed, the sound volume
cannot be checked. Execution is possible.
4) When [EXECUTE] button is pressed, it is highlighted and deliv-
ery of the on-hold tone is stopped.
SIMULATION NO.66-22
TEST
HANDSET VOLUME SETTING
A 1 (0:MIN 1:MIDDLE 2:MAX)
A:
1
0 2
66-24
Purpose : Data clear
Function (Purpose) : Used to clear the FAST save data.
Section : FAX
Item : Data clear
Operation/Procedure
1) Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.
2) Press [YES] button.
The FAST save data are cleared. [YES] button is highlighted.
* When [NO] button is pressed, [EXECUTE] button returns to
the normal display and [YES] and {NO} buttons gray out.
* During execution of the FAST save data clear, [EXECUTE]
and [YES] buttons are highlighted.
3) After completion of memory clear, [EXECUTE] button returns
to the normal display and [YES] and {NO} buttons gray out.
66-25
Purpose : Setting
Function (Purpose) : Used to register the FAX number for
MODEM dial-in.
Section : FAX
Item : Data clear
CLOSE
EXECUTE OK
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 15
Operation/Procedure
1) When the machine enters Simulation 66-25, the following
screen is displayed.
* The stored number is displayed in the column of
"PRESENT:". (If there is no data, [-------] is displayed.)
2) Enter a number with 10-key.
Entry can be made up to 20 digits.
After entering 20 digits. 10-key is disabled. Only [C] key is
enabled.
The entered number is displayed in the column of "NEW:".
(10-key [0] to [9], [*], [#], [C] key (back by one digit))
3) When [SET] button is pressed after completion of entering a
number, the entered umber is displayed (registered) in the col-
umn of "PREZENT:".
The column of "NEW:" becomes blank.
* When the column of "NEW:" is blank, [SET] becomes inac-
tive. When a number is entered to "NEW:", [SET] becomes
active.
SIMULATION NO.66-25
TEST
M-D-IN FAX NUMBER SETTING. 0-9[0-9].*:[*]:#:[#]
PRESENT ---------------------
:
NEW
:
66-26
Purpose : Setting
Function (Purpose) : Used to register external telephone num-
bers for MODEM dial-in.
Section : FAX
Item : Data (Registration)
Operation/Procedure
1) When the machine enters Simulation 66-26, the screen on the
right is displayed.
* The stored number is displayed in the column of
"PRESENT:". (If there data, [-------] is displayed.)
2) Enter a number with 10-key. Entry can be made up to 20 digits.
After entering 20 digits. 10-key is disabled. Only [C] key is
enabled.
The entered number is displayed in the column of "NEW:". (10-
key [0] to [9], [*], [#], [C] key (back by one digit))
3) When [SET] button is pressed after completion of entering a
number, the entered umber is displayed (registered) in the col-
umn of "PRESENT:".
The column of "NEW:" becomes blank.
* When the column of "NEW:" is blank, [SET] becomes inac-
tive. When a number is entered to "NEW:", [SET] becomes
active.
SIMULATION NO.66-26
TEST
M-D-IN EXTEL NUMBER SETTING. 0-9[0-9]*:[*]:#:[#]
PRESENT: -----------------
NEW:
CLOSE
SET
CLOSE
SET