Sharp MX-FXX1 Service Manual page 68

Report code
Display in the column of
(Communication
result
result)
85 NG85 XXXX *1
86 RECEIVED
87 NG87 XXXX *1
88 NG88 XXXX *1
89 NG89 XXXX *1
90 NG90 XXXX *1
91 NG91 XXXX *1 *2
92 NG92 XXXX *1 *2
98 NG98 XXXX *1
99 NG99 XXXX *1
*1: For a job status result in "Display in the column of result," "NG
For a communication result, "Communication error
*2: The error code of Scan To USB is specified only in the job log.
• When the communication result is OK, the communication sub code 1 and the communication sub code 2 are "0000."
• Errors in ( ) are not used.
B. Communication report sub code 1
The communication report sub code 1 (upper 2 digits) are always indicated as "00."
C. Communication report sub code 2
Report code 2
1 Send length over
2 EOL time up
3 Carrier detection time up
4 Not used
5 Time up in phase C (8 min)
6 Memory image decode error
7 Memory image decode error
8 Time up between frames in phase C (Report code is 0 or 16.)
9 Not used
10 Not used
11 Polarity reversion detection
12 Invalid command reception
13 Time up (1-minute timer/6-second time)
14 PUT error
15 In V.34 mode, time up is generated when shifting from Primary to Control.
16 In V.34 mode, time up is generated when shifting from Control to Primary.
17 Command receive time-up from MFP controller
18 Not used
19 Not used
20 Polarity reversion detection
21 Invalid command reception
22 Fallback retry number over
23 Command retry number resend over
24 Time up (T5 timer)
25 Time up (T5 timer) in V.34 mode
26 In V.34 mode, time up is generated when shifting from Primary to Control.
27 In V.34 mode, time up is generated when shifting from Control to Primary.
28 Not used
29 Not used
30 A communication error is generated between MFP controller and Modem controller. (Report code is 0 or 16.)
31 DC current not detected (busy)
32 Dial tone not detected (busy)
33 Busy tone detection (busy)
34 T0 time up (Remote machine not responding)
35 T1 time up (Remote machine not responding)
36 In dialing, polarity reversion detection (Remote machine not responding)
Content of communication interruption
In e-mail receive, an error occurs in communication with POP3 server.
• Header acquisition error.
• Time-out during mail receive
In e-mail receive, an unsupported attached file is received.
Only the TIFF-F type is supported for attached files.
• The TIFF-F type of the attached file cannot be recognized.
• There is no attached file.
In e-mail receive, an attached file cannot be stored in memory.
• Memory over
In SMTP e-mail receive, an attached file cannot be stored in memory.
• Cannot be stored in memory.
• The number of items of acting receive data is the maximum, and an additional data cannot be stored.
In SMTP e-mail receive, an error occurs in communication with the mail server.
• Time-out occurs during e-mail receive.
After reservation by re-operation of document filing, conversion for image send cannot be made.
Data cannot be written to the memory device when Scan To USB is executed.
• The memory device is disconnected during writing to the memory device.
• An error occurs due to a memory device trouble.
The USB device memory overflows during writing data into the memory device when "Scan to USB" is
executed.
The copy inhibit pattern is detected when scanning a document.
A document which is inhibited to be copied such as a banknote is scanned.
XXXX" is displayed. "
(XXXX)" is displayed.
Content of communication interruption
MXFXX1 TROUBLE CODE 6 – 4
" is the code number.
Send/Receive
Send
Receive
Receive
—
Send
Receive
Send
Send/Receive
—
—
Receive
Receive
Receive
Receive
Receive
Receive
Receive
—
—
Send
Send
Send
Send
Send
Send
Send
Send
—
—
—
Send
Send
Send
Send
Send
Send