Sharp MX-FXX1 Service Manual page 26

66-33
Purpose : Operation test/Check
Function (Purpose) : Used to execute detection of various sig-
nals with the line connected and to display
the detection result. When a signal is
detected, the display is highlighted.
Section : FAX
Item : Operation
Operation/Procedure
1) When the machine enters Simulation 66-33, the following
screen is displayed.
2) When a signal is detected, "FNET" and"BUSY TONE CNG
CED DTMF"are highlighted. When a signal is not detected,
they are normally displayed.
<Signal used for signal detection check>
(When "FNET" is selected)
FNET
(When "BT/CNG/CED/DTMF" is selected)
BUSY TONE CNG
SIMULATION NO.66-33
TEST
SIGNAL DETECT CHECK.
FNET
BT/CNG/CED/DTMF
66-34
Purpose : Operation test/Check
Function (Purpose) : Used to execute the send test and display
the time required for sending image data in
the test. Used to execute send test and dis-
play. (Unit: ms)
Section : FAX
Item : Operation
Operation/Procedure
1) When the machine enters Simulation 66-34, the following
screen is displayed.
2) When image data are actually sent, the time required for send-
ing the image data is displayed on the LCD.
* #### : Time
66-36
Purpose : Operation test/Check
Function (Purpose) : Used to check send and receive data from
the MODEM controller to the MFP control-
ler or the data line or the command line
individually.
Section : FAX
Item : Operation
CED DTMF
CLOSE
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 17
Operation/Procedure
1) When the machine enters Simulation 66-36, the following
screen is displayed. (Default: left upper selected)
2) Operation check
Select an item to be checked on the screen.
* When an item to be checked is selected, it is highlighted.
3.1. When "Operation check once" is selected:
● When (once) is selected:
When [EXECUTE] button is pressed under this state, [EXECUTE]
button is highlighted and the operation check is started.
After completion of the operation check, [EXECUTE] button returns
to the normal display and the check result is displayed.
When the check is normally completed, "OK" is displayed. In case
of an error, [NG" is displayed.
3.2. When "Operation check repeat" is selected:
● When [repeat] is selected:
When [EXECUTE] button is pressed under this state, [EXECUTE]
button is highlighted and the operation check is started.
* In the case of [Repeat] check, the title display is changed as fol-
lows for every execution of check.
"MFP-MDMC I/F CHECK.- *"
"MFP-MDMC I/F CHECK.- **"
"MFP-MDMC I/F CHECK.- ***"
"MFP-MDMC I/F CHECK.- ****"
"MFP-MDMC I/F CHECK.- *****"
Check is repeated until [EXECUTE] button is pressed or "NG"
occurs.
To stop the operation check, press [EXECUTE] button, and
[EXEUTE] button returns to the normal display and the operation
check is terminated.
* When an abnormality occurs during check, "NG" is displayed
and the operation is terminated.
<MFP controller I/F check item table>
MFP ← MDMC (DATA once)
Data line Once
MFP ← MDMC (DATA repeat)
Data line Repeat
MFP ← MDMC (CMD once)
Command line Once
MFP ← MDMC (CMD repeat)
Command line Repeat
SIMULATION NO.66 36
TEST
MFP-MDMC I/F CHECK.
MFP<-MDMC (DATA once)
MFP<-MDMC(DATA repeat)
MFP<-MDMC (CMD once)
MFP<-MDMC (CMD repeat)
66-39
Purpose : Setting
Function (Purpose) : Used to check and change the destination
setting saved in EEPROM of the FAX BOX.
Section : FAX
Item : Specifications
Operation/Procedure
1) When the machine enters the simulation, the currently set des-
tination button is highlighted. (In the default state, JAPAN is set
as the destination.)
MFP → MDMC (DATA once)
Data line Once
MFP → MDMC (DATA repeat)
Data line Repeat
MFP → MDMC (CMD once)
Command line Once
MFP → MDMC (CMD repeat)
Command line Repeat
CLOSE
MFP->MDMC (DATA once)
MFP->MDMC(DATA repeat)
MFP>MDMC (CMD once)
MFP->MDMC (CMD repeat)
EXECUTE