Sharp MX-FXX1 Service Manual page 32

SW Bit
Item
No. No.
15 1-8 Signal sending level
16 1-8 Not used
17 1 Automatic reduced
transmission
2 Rotated transmission
selection (A4 → A4R)
3 Rotated transmission
selection (B5R → B5)
4 Rotated transmission
selection (A5R → A5)
5 Rotated transmission
selection
(8.5 x 11 → 8.5 x 11R)
6 Rotated transmission
selection
(16K → 16KR)
7 Rotated transmission
selection (5.5 x 8.5R →
5.5 x 8.5)
SW16, 1-8 Initial value
"00000000": North America/Taiwan/Middle East/Other3
"00010000": China/Hong Kong
"00110000": India
"01010000": Indonesia/Thailand/Malaysia/Philippine
"01100000": Singapore/South Africa
"10000000": U.K./France/Germany/Sweden/Finland/Norway/Denmark/Netherlands/Italy/Switcherland/Austria/New Zealand/Slovakia/Spain/Portuguese/
Luxemburg/Belgium/Czech/Hungary/Greece/Poland
"10100000": Australia/Rusia
SW selection and function
Set the level adjustment for sending signals from the modem. Setting
can be made over the range of 0 to 26 in 1dBm increments by binary
inputting.
Since the maximum level differs according to country, if a value above
the maximum level is set, the maximum value for the present country
code will be adopted.
In cases where the transmitted document size (width) is larger than the
FAX paper size (width) of the other party's machine, this setting
determines whether to reduce the transmitted document or to cut off
both edges.
"0": Transmit in reduced size
"1": Do not transmit in reduced size
Rotated transmission or not depending on orientation of the document.
When transmitting A4 document, this setting determines whether to
transmit as A3 width (A4) or to rotate the read image and transmit as A4
width (A4R).
"0": Rotate
"1": Do not rotate
Rotated transmission or not depending on orientation of the document.
When transmitting B5R document, this setting determines whether to
transmit as A4 width (B5R) or to rotate the read image and transmit as
B4 width (B5).
"0": Rotate
"1": Do not rotate
Rotated transmission or not depending on orientation of the document.
When transmitting A5R document, this setting determines whether to
transmit as A4 width (A5R) or to rotate the read image and transmit as
A4 width (A5).
"0": Rotate
"1": Do not rotate
Rotated transmission or not depending on orientation of the document.
When transmitting 8.5 x 11 (LTR) document, this setting determines
whether to transmit as A3 width (8.5 x 11) or to rotate the read image
and transmit as A4 width (8.5 x 11R).
"0": Rotate
"1": Do not rotate
Rotated transmission or not depending on orientation of the document
(16K A4).
When transmitting 16K document, this setting determines whether to
transmit as A3 width (16K) or to rotate the read image and transmit as
A4 width (16KR).
"0": Rotate
"1": Do not rotate
Rotated transmission or not depending on orientation of the document
(INVOICE A5).
When transmitting 5.5 x 8.5R (INVOICE-R) document, this setting
determines whether to transmit as A4 width (5.5 x 8.5R) or to rotate the
read image and transmit as A4 width (5.5 x 8.5).
"0": Rotate
"1": Do not rotate
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 23
Initial value
0 "00001010": -10dBm Adjustment
(North America/China/ value
0
Singapore/Thailand/
0
Malaysia/Philippine/Hong
0
Kong/Middle East/Other3)
1
"00001001": -9dBm (U.K./
0
France/Germany/Sweden/
1
Finland/Norway/Denmark/
0
Netherlands/Italy/
Switcherland/Austria/
Indonesia/Slovakia/South
Africa/Spain/Portuguese/
Luxemburg/Belgium/
Czech/Hungary/Greece/
Poland)
"00001011": -11dBm
(Australia/New Zealand/
India/Taiwan/Rusia)
0 Refer to "SW16, 1-8 Initial
value"
0 Transmit in reduced size. FAX
transmission
setting
0 Rotate FAX
transmission
setting
0 Rotate FAX
transmission
setting
0 Rotate FAX
transmission
setting
0 Rotate FAX
transmission
setting
0 Rotate FAX
transmission
setting
0 Rotate FAX
transmission
setting
System
settings