Table of Contents
Advertisement
IMPORTANT NOTES
Power Supply
301
•
Do not connect this unit to same electrical outlet that is being used by an
electrical appliance that is controlled by an inverter (such as a refrigerator,
washing machine, microwave oven, or air conditioner), or that contains a motor.
Depending on the way in which the electrical appliance is used, power supply
noise may cause this unit to malfunction or may produce audible noise. If it is
not practical to use a separate electrical outlet, connect a power supply noise
filter between this unit and the electrical outlet.
307
•
Before connecting this unit to other devices, turn off the power to all units. This
will help prevent malfunctions and/or damage to speakers or other devices.
308
•
Although the LCD and LEDs are switched off when the POWER switch is
switched off, this does not mean that the unit has been completely discon-
nected from the source of power. If you need to turn off the power completely,
first turn off the POWER switch, then unplug the power cord from the power
outlet. For this reason, the outlet into which you choose to connect the power
cord's plug should be one that is within easy reach and readily accessible.
Placement
352a
•
This device may interfere with radio and television reception. Do not use this
device in the vicinity of such receivers.
352b
•
Noise may be produced if wireless communications devices, such as cell phones,
are operated in the vicinity of this unit. Such noise could occur when receiving
or initiating a call, or while conversing. Should you experience such problems,
you should relocate such wireless devices so they are at a greater distance from
this unit, or switch them off.
354a
•
Do not expose the unit to direct sunlight, place it near devices that radiate heat,
leave it inside an enclosed vehicle, or otherwise subject it to temperature
extremes. Excessive heat can deform or discolor the unit.
355b
•
When moved from one location to another where the temperature and/or
humidity is very different, water droplets (condensation) may form inside the
unit. Damage or malfunction may result if you attempt to use the unit in this
condition. Therefore, before using the unit, you must allow it to stand for several
hours, until the condensation has completely evaporated.
360
•
Depending on the material and temperature of the surface on which you place
the unit, its rubber feet may discolor or mar the surface.\nYou can place a piece
of felt or cloth under the rubber feet to prevent this from happening. If you do
so, please make sure that the unit will not slip or move accidentally.
Maintenance
401a
•
For everyday cleaning wipe the unit with a soft, dry cloth or one that has been
slightly dampened with water. To remove stubborn dirt, use a cloth impreg-
nated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit
thoroughly with a soft, dry cloth.
402
•
Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possi-
bility of discoloration and/or deformation.
Repairs and Data
452
•
Please be aware that all data contained in the unit's memory may be lost when
the unit is sent for repairs. Important data should always be backed up on USB
memory, or written down on paper (when possible). During repairs, due care is
taken to avoid the loss of data. However, in certain cases (such as when circuitry
related to memory itself is out of order), we regret that it may not be possible to
restore the data, and Roland assumes no liability concerning such loss of data.
6
Additional Precautions
•
This unit allows you to switch images or turn video effects on/off at high speed.
For some people, viewing such images can cause headache, nausea, or other
discomfort. Do not use this unit to create video that might cause these types of
health problems. Roland Corporation will accept no responsibility for any such
health problems that may occur in yourself or in viewers.
551
•
Please be aware that the contents of memory can be irretrievably lost as a result
of a malfunction, or the improper operation of the unit. To protect yourself
against the risk of loosing important data, we recommend that you periodically
save a backup copy of important data you have stored in the unit's memory on
USB memory.
552
•
Unfortunately, it may be impossible to restore the contents of data that was
stored in the unit's memory once it has been lost. Roland Corporation assumes
no liability concerning such loss of data.
553
•
Use a reasonable amount of care when using the unit's buttons, sliders, or other
controls; and when using its jacks and connectors. Rough handling can lead to
malfunctions.
554
•
Never strike or apply strong pressure to the display.
555
•
A small amount of noise may be heard from the display during normal
operation.
556
•
When connecting / disconnecting all cables, grasp the connector itself—never
pull on the cable. This way you will avoid causing shorts, or damage to the
cable's internal elements.
557
•
A small amount of heat will radiate from the unit during normal operation.
559a
•
When you need to transport the unit, package it in the box (including padding)
that it came in, if possible. Otherwise, you will need to use equivalent packaging
materials.
988
•
Security Slot (
)
http://www.kensington.com/
•
This product is a Class A digital device under FCC part 15 for use in other than
residential environment. Use of this equipment in a residential environment
may cause radio interference requiring the user to take appropriate preven-
tative measures. In such instances, take steps such as using cables with ferrite
cores near their connectors.
For information on specific preventive methods, contact your dealer, the
nearest Roland Service Center, or an authorized Roland distributor, as listed on
the "Information" sheet.
•
This product is a Class A digital device under FCC Part 15 designed to be used in
a non-residential environment. When this device is connected to a video
cameras or other such Class B equipment, the system as a whole is then
classified as a Class A device. Use of this equipment in a residential environment
may cause radio interference requiring the user to take appropriate preventive
measures.
In such instances, take steps such as using cables with ferrite cores near their
connectors.
For information on specific preventive methods, contact your dealer, the
nearest Roland Service Center, or an authorized Roland distributor, as listed on
the "Information" sheet.
Hide quick links:
Advertisement
Table of Contents
