Reverb Parameters; Copying Effect Settings - Roland XV-5050 Owner's Manual

Reverb Parameters

These settings allow you to select the desired type of reverb and its
characteristics.
Parameter Value
Type 0 (OFF),
1 (REVERB),
2 (SRV
ROOM),
3 (SRV
HALL),
4 (SRV
PLATE),
5 (GM2 RE-
VERB)
Type: 1 (REVERB)
Reverb Type ROOM1,
ROOM2,
STAGE1,
STAGE2,
HALL1,
HALL2,
DELAY,
PAN-DELAY
Reverb Time 0-127
Rev HF Damp 200-8000 Hz,
BYPASS
Reverb Feedback 0-127
Type: 2 (SRV ROOM) / 3 (SRV HALL) / 4 (SRV PLATE)
Pre Delay
0.0-100.0 ms
Time 0-127
Size 1-8
High Cut 160 Hz-12.5
kHz, BYPASS
Density 0-127
Diffusion
0-127
LF Damp 50-4000 Hz,
BYPASS
LF Damp Gain -36-0 dB
HF Damp 4000 Hz-12.5
kHz, BYPASS
HF Damp Gain -36-0 dB
Type: 5 (GM2 REVERB)
Level 0-127
Character 0-7
Pre-LPF 0-7
Time 0-127
Delay Feedback 0-127
Description
Type of reverb
0 (OFF): Reverb is not used.
1 (REVERB): Normal reverb
2 (SRV ROOM): This simulates typical
room acoustic reflections.
3 (SRV HALL): This simulates typical
concert hall acoustic reflections.
4 (SRV PLATE): This simulates a reverb
plate, a popular type of artificial reverb
unit that derives its sound from the vi-
bration of a metallic plate.
5 (GM2 REVERB): GM2 Reverb
Type of reverb/delay
ROOM1: short reverb with high density
ROOM2: short reverb with low density
STAGE1: reverb with greater late rever-
beration
STAGE2: reverb with strong early re-
flections
HALL1: very clear-sounding reverb
HALL2: rich reverb
DELAY: conventional delay effect
PAN-DELAY: delay effect with echoes
that pan left and right
Time length of reverberation (Type:
ROOM1-HALL2)
Delay time (Type: DELAY, PAN-DELAY)
Adjusts the frequency above which the
high-frequency content of the reverb sound
is cut, or "damped." If you don't want to
damp the high frequencies, set this parame-
ter to BYPASS.
Adjusts the amount of delay feedback when
the Type setting is DELAY or PAN-DELAY.
Adjusts the time until the reverb is heard.
Duration of reverb
Size of the simulated room or hall
Adjusts the frequency above which the
high-frequency content of the reverb is fil-
tered out. If you don't want to reduce the re-
verb's high frequencies, set this parameter
to BYPASS.
Density of reverb
Adjusts the change in the density of the re-
verb over time. The higher the value, the
more the density increases with time. (The
effect of this setting is most pronounced
with long reverb times.)
Adjusts the frequency below which the low-
frequency content of the reverb sound is re-
duced, or "damped." If you don't want to
damp the high frequencies, set this parame-
ter to BYPASS.
Adjusts the amount of damping applied to
the frequency range selected with LF Damp.
With a setting of "0," there's no reduction of
the reverb's low-frequency content.
Adjusts the frequency above which the
high-frequency content of the reverb sound
is reduced, or "damped." If you don't want
to damp the high frequencies, set this pa-
rameter to BYPASS.
Adjusts the amount of damping applied to
the frequency range selected with HF
Damp. With a setting of "0," there's no re-
duction of the reverb's high-frequency con-
tent.
Output level of reverbration
Type of reverb
0–5: reverb
6, 7: delay
Cuts the high frequency range of the sound
coming into the reverb.
Higher values cut more high frequencies.
Duration of reverb
Adjusts the amount of the delay sound
that's fed back into the effect when the Re-
verb Character setting is 6 or 7.
Chapter 4 Using the XV-5050 Effects

Copying Effect Settings

You can copy the effect settings from any Patch, Performance, or
Rhythm Set into the currently selected Patch, Performance, or
Rhythm Set. This can save a great deal of time and effort when
setting up effects.
1. Make sure that the Performance, Patch or Rhythm Set you
wish to copy is selected.
2. Press [UTILITY] to make its indicator light.
3. Press [
CURSOR] a few times to move the cursor to the
parameter group at the upper line of the display.
4. Turn [VALUE] to choose "COPY EFFECT."
5. USE [
CURSOR]/[CURSOR
the desired settings.
6. Press [ENTER] to execute the Copy.
* To cancel, press [EXIT].
7. Press [EXIT] to return to the appropriate PLAY screen.
A "*" symbol will appear at the left of the Patch/Performance/
Rhythm Set name, indicating that the Copy has been executed.
Parameter Value
Source PERFORM, PATCH,
RHYTHM
(Performance/Patch/Rhythm Set name)
Type MFX, CHORUS, RE-
VERB
From MFX-A–C
To MFX-A–C
] and [VALUE] to choose
Description
Selects the source containing
the settings you wish to copy.
Selects the effect type of the
source.
Selects the Multi-effects to
copy the settings from.
* This can be set only when
"PERFORM" is selected for
Source and "MFX" is select-
ed for Type.
Selects the Multi-effects to
which you want to copy the
settings.
* This can be set only when
"PERFORM" is selected for
Source and "MFX" is select-
ed for Type.
103