Create Cpu Access_Profile - D-Link DES-3010F Command Line Interface Reference Manual

DES-30XX Layer 2 Switch CLI Reference Manual

create cpu access_profile

Purpose
Used to create an access profile specifically for CPU Interface Filtering
on the Switch and to define which parts of each incoming frame's header
the Switch will examine. Masks can be entered that will be combined with
the values the Switch finds in the specified frame header fields. Specific
values for the rules are entered using the config cpu access_profile
command, below.
Syntax create cpu access_profile profile_id <value 1-3> [ethernet {vlan |
source_mac <macmask> | destination_mac <macmask> | 802.1p |
ethernet_type} | ip {vlan | source_ip_mask <netmask> |
destination_ip_mask <netmask> | dscp | [icmp {type | code} | igmp
{type} | tcp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex
0x0-0xffff>} | flag_mask [all | {urg | ack | psh | rst | syn | fin}]} |
udp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-
0xffff>} | protocol_id_mask {user_mask <hex 0x0-0xffffffff>} ]} |
packet_content_mask {offset 0-15 <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>| offset 16-31 <hex
0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> | {offset 32-47 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex
0x0-0xffffffff> <hex 0x0-0xffffffff> | {offset 48-63 <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | {offset
64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff>} | ipv6 {class | flowlabel | source_ipv6_mask
<ipv6mask> | destination_ipv6_mask <ipv6mask}]
Description
The create cpu access_profile command is used to create an access
profile used only for CPU Interface Filtering. Masks can be entered that
will be combined with the values the Switch finds in the specified frame
header fields. Specific values for the rules are entered using the config
cpu access_profile command, below.
Parameters
profile_id <value 1-3> − Specifies an index number that will identify the
access profile being created with this command.
ethernet − Specifies that the Switch will examine the layer 2 part of each
packet header.
vlan − Specifies that the Switch will examine the VLAN part of each
•
packet header.
source_mac <macmask> - Specifies to examine the source MAC
•
address mask.
destination_mac <macmask> - Specifies to examine the destination
•
MAC address mask.
802.1p − Specifies that the Switch will examine the 802.1p priority
•
value in the frame's header.
ethernet_type − Specifies that the Switch will examine the Ethernet
•
type value in each frame's header.
ip − Specifies that the Switch will examine the IP address in each frame's
header.
vlan − Specifies a VLAN mask.
•
source_ip_mask <netmask> − Specifies an IP address mask for the
•
source IP address.
114