D-Link DES-3010F Command Line Interface Reference Manual page 117

Command
create cpu
access_profile
delete cpu
access_profile
config cpu
access_profile
enable
cpu_interface_filtering
disable
cpu_interface_filtering
show
cpu_access_profile
Each command is listed, in detail, in the following sections.
DES-30XX Layer 2 Switch CLI Reference Manual
Parameters
profile_id <value 1-3> [ethernet {vlan | source_mac <macmask> | destination_mac
<macmask> | 802.1p | ethernet_type} | ip {vlan | source_ip_mask <netmask> |
destination_ip_mask <netmask> | dscp | [icmp {type | code} | igmp {type} | tcp
{src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} | flag_mask [all |
{urg | ack | psh | rst | syn | fin}]} | udp {src_port_mask <hex 0x0-0xffff> |
dst_port_mask <hex 0x0-0xffff>} | protocol_id_mask {user_mask <hex 0x0-
0xffffffff>} ]} | packet_content_mask {offset 0-15 <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>| offset 16-31 <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | {offset 32-47 <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | {offset 48-63
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> |
{offset 64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff>} | ipv6 {class | flowlabel | source_ipv6_mask <ipv6mask> |
destination_ipv6_mask <ipv6mask}]
profile_id <value 1-3>
profile_id <value 1-3> [add access_id <value 1-5> [ethernet {vlan <vlan_name 32>
| source_mac <macaddr> | destination_mac <macaddr> | 802.1p <value0-7> |
ethernet_type <hex 0x0-0xffff>} | ip {vlan <vlan_name 32> | source_ip <ipaddr> |
destination_ip <ipaddr> | dscp <value 0-63> | [icmp {type <value 0-255> code
<value 0-255>} | igmp {type <value 0-255>} | tcp {src_port <value 0-65535> |
dst_port <value 0-65535> | {urg | ack | psh | rst | syn | fin}]} | udp {src_port <value 0-
65535> | dst_port <value 0-65535>} | protocol_id <value 0 - 255> {user_define <hex
0x0-0xffffffff>}]} | packet_content {offset_0-15 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff>| offset_16-31 <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_32-47 <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_48-63 <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_64-79
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>}] | ipv6
{class <value 0-255> | flowlabel <hex 0x0-0xfffff> | source_ipv6 <ipaddr> |
destination_ipv6 <ipv6addr>} port [<portlist> | all] [permit | deny] | delete access_id
<value 1-5>]
profile_id <value 1-3>
113