Multi 7.1: Bus; 1: Bus; 3: Route (Routing) - Korg Triton-Rack Parameter Manual

MULTI 7.1: BUS

Specifies the bus to which the program oscillator(s) of each
track 1–8, 9–16 will be sent. You can also set the amount of
signal that will be sent to the master effects.
For details on insert effects, refer to "8. Effect Guide"
p.146.
7.1–1: BUS..8
(BUS T01–08)
7.1–2: BUS..16
(BUS T09–16)
7.1–1a
7.1–1(2)a: BUS Select, Send1(MFX1), Send2(MFX2)
BUS Select [DKit, L/R, IFX1...5, 1...4, 1/2, 3/4, Off]
Specifies the output bus for the program oscillators of tracks
1–8 and 9–16.
The state of the settings can be viewed in the Route page.
( COMBI 7.1–1a)
S1 (Send1(MFX1))
S2 (Send2(MFX2))
Here you can adjust the send levels from tracks 1–8, 9–16 to
master effects 1 and 2. This is valid when "BUS Select" is set
either to L/R or Off. If IFX 1, 2, 3, 4, or 5 is selected, the send
level to the master effects 1 and 2 is set by the "S1
(Send1(MFX1))" and "S2 (Send2(MFX2))" parameters
located in the 7.2: Insert FXl, Setup page, after the signal
passes through IFX 1–5.
These settings have no effect if "BUS Select" is set to 1, 2, 3,
4, 1/2 or 3/4.
If "Status" (3.1–1a/2a) is either INT or BTH, CC#93
and #91 can be received to control send 1 and 2 respec-
tively and change their settings. When you switch
multi, tracks whose "Status" is EXT, EX2 or BTH will
transmit these settings via MIDI. This data will be
transmitted on the MIDI channel of each track as set by
"MIDI Channel" (3.1–1a/2a). The actual send level is
determined by multiplying the value of these parame-
ters with the send level settings of the oscillator(s) of
the program used by the track ("S1 (Send1(MFX1))"
and "S2 (Send2(MFX2))" PROG 7.2–1a).
7.1–1(2)b: UTILITY
"Memory Status" (1.1–1c), "DKit IFX Patch" (COMBI 7.1–
1b)
Copy Insert Effect
( PROG 7.1–1c)
Note, the MIDI control channel specified in "Control Chan-
nel" of the 7.2: Insert FX, Setup page will not be copied.
Swap Insert Effect
( PROG 7.1–1c)
Note, the MIDI control channel specified in "Control Chan-
nel" of the 7.2: Insert FX, Setup page will not be swapped.
7.1–3: Route
7.1–3a
7.1–1b
7.1–3a: Routing Map, BUS Select
This shows the status of the insert effects: the insert effect
routing, the names of the selected effects, the on/off status,
and chaining. The effect type, on/off, and chain settings can
be made in the 7.2: Insert FX, Setup page.
T01...16: BUS Sel
[000...127]
You can specify the bus to which the program oscillators of
tracks 1–16 will be sent, while viewing a map of the current
[000...127]
settings.
Use the [ ], [ ] keys to select the track, and use the [INC],
[DEC] keys or the [VALUE] dial to set "BUS Select" (7.1–1a/
2a).
These settings can also be made from "BUS Select" (7.1–1/
2).
7.1–3b: UTILITY
"Memory Status" (1.1–1c), "Copy Insert Effect," "Swap
Insert Effect" (7.1–1b/2b), "DKit IFX Patch" (COMBI 7.1–
1b)
(Routing)
[DKit, L/R, IFX1...5, 1...4,1/2, 3/4, Off]
7.1–3b
69