2: Pref. (System Preference) - Korg Triton-Rack Parameter Manual

Write Global Setting
This command writes Global mode settings (except for
Drum Kits and User Arpeggio Patterns).
1 Select "Write Global Setting" to access the dialog box.
2 To write the data, press the [F8] ("OK") key. To cancel
without writing, press the [F7] ("Cancel") key.
You can also use the [WRITE] key to write data in the
same way as the "Write Global Setting" command.
Press the [WRITE] key to access the "Update Global Set-
ting" dialog box, and press the [F8] key to write the data.
To write a drum kit or user arpeggio pattern, execute the
appropriate utility. ( 5.1–1d "Write Drum Kits," 6.1–1d
"Write Arpeggio Patterns")
Change all bank references
This command changes all program banks specified for tim-
bres in combinations or tracks of multis.
1 Select "Change all bank references" to access the dialog
box.
2 To execute this command for combinations, check
"Combi." To execute this command for multis, check
"Multi." If you check "Multi," the program banks within
the event data of the multis will also be changed.
3 Specify the banks to be changed ("Program Bank").
4 To execute the Change All Bank References command,
press the [F8] ("OK") key. To cancel without executing,
press [F7] ("Cancel") key.
If you change two or more different banks to the same
bank, it will not be possible to use this function to
change them back to different banks. Be careful that the
change destination banks do not overlap.
1.1–2: Pref.
(System Preference)
1.1–2a
1.1–2a: System Preference
Bank Map
Specifies the mapping of programs and combinations rela-
tive to Bank Select control change messages (CC#0 upper
byte and CC#32 lower byte).
The bank select messages shown in the following table can
be received (R) or transmitted (T), corresponding to Pro-
gram banks I–A...I–F (only for the separately sold EXB-
MOSS option), banks G, g (1)–g(9), g(d), E–A...E–H and
Combination banks I–A...I–E and E–A...E–H.
Bank Bank Map: KORG
I–A 00. 00 R/T
I–B 00. 01 R/T
I–C 00. 02 R/T
I–D 00. 03 R/T
I–E 00. 04 R/T
I–F 00. 05 R/T
G, 79. 00, 79. 01...09 R/T
g (0)...g (9)
38. 00 R
g (d) 78. 00 R/T
3E. 00 R
E–A 00. 08 R/T
E–B 00. 09 R/T
E–C 00. 0A R/T
E–D 00. 0B R/T
E–E 00. 0C R/T
E–F 00. 0D R/T
E–G 00. 0E R/T
E–H 00. 0F R/T
Power On Mode
Specifies the condition at power-on.
Reset: The TRITON-Rack will be in Combination mode
COMBI 1.1: Play, and Combination I–A000 will be selected.
Memorize: The location (mode and page) where you were
when the power was last turned off, and the last-selected
program or combination number will be selected.
This function does not memorize the contents of any
parameters that were edited. Before turning off the
power, be sure to write your data or save it in Disk
mode.
1.1–2b 1.1–2c
[KORG, GM(2)]
Bank Map: GM(2)
3F. 00 R/T
3F. 01 R/T
3F. 02 R/T
3F. 03 R/T
3F. 04 R/T
3F. 05 R/T
79. 00, 79. 01...09 R/T
38. 00 R
00. 00, 00. 01...(XG) R
00. 00, 01. 00...(GS) R
78. 00 R/T
3E. 00 R
3F. 7F R (→Korg MUTE)
3F. 08 R/T
3F. 09 R/T
3F. 0A R/T
3F. 0B R/T
3F. 0C R/T
3F. 0D R/T
3F. 0E R/T
3F. 0F R/T
[Reset, Memorize]
109