2: Mod. (Amp1 Modulation) - Korg Triton-Rack Parameter Manual

5.1–2: Mod.
(Amp1 Modulation)
These settings allow you to apply modulation to amp 1 (for
oscillator 1) to modulate the volume.
5.1–2a
5.1–2b
5.1–2a: Keyboard Track
These parameters let you use keyboard tracking to adjust
the volume of oscillator 1. Use the "Key" and "Ramp"
parameters to specify how the volume will be affected by
the keyboard location that you play.
Key (Keyboard Track Key):
Specifies the note number at which keyboard tracking will
begin to apply.
The volume will not change between "Low (KBDTrk Key
Low)" and "High (KBDTrk Key High)."
You can also input the note number by holding down
the [ENTER] key and playing a note on a connected
MIDI device.
Low (KBDTrk Key Low)
Keyboard tracking will apply to the range of notes below the
note number you specify here.
High (KBDTrk Key High)
Keyboard tracking will apply to the range of notes above the
note number you specify here.
Ramp (Ramp Setting):
Specifies the angle of the keyboard tracking.
Low (KBDTrk Ramp Low)
With positive (+) values of this parameter, the volume will
increase as you play notes below the "Low (KBDTrk Key
Low)" note number. With negative (–) values, the volume
will decrease.
High (KBDTrk Ramp High)
With positive (+) values of this parameter, the volume will
increase as you play notes above the "High (KBDTrk Key
High)" note number. With negative (–) values, the volume
will decrease.
Volume change produced by keyboard location and Ramp settings
Volume
Ramp Low=+99
Ramp Low=0
Ramp Low=–99
KBDTrk Low
5.1–2b: Amp Mod., LFO1 Mod., LFO2 Mod.
Indicates settings to specify how the volume of oscillator 1
will be controlled by velocity, OSC1 LFO1, and OSC1 LFO2.
20
5.1–2c
[C–1...G9]
[C–1...G9]
[–99...+99]
[–99...+99]
Ramp High=+99
Ramp High=0
Ramp High=–99
Key
KBDTrk High
Amp Mod. (Amp Modulation)
Velocity Int. (Amp Velocity Int.)
With positive (+) values, the volume will increase as you
play more strongly.
With negative (–) values, the volume will decrease as you
play more strongly.
Volume change (with positive (+) values of this parameter)
Note-on
Note-off
Softly played
AMS (Amp AMS)
Selects the source that will control the volume of amp 1
( p.206 "AMS List") (EXT) Velocity cannot be selected.
Int. (AMS Intensity)
Specifies the depth and direction of the effect that "AMS
(Amp AMS)" will have.
The actual volume will be determined by multiplying the
value of the changes produced by the amp EG with the val-
ues of Alternate Modulation etc., and if the levels of the amp
EG are low, the modulation applied by Alternate Modula-
tion will also be less.
For example, if you set "AMS (Amp AMS)" to AfterT and
press down on the keyboard of a connected MIDI instru-
ment, the volume will increase if you have set this parame-
ter to a positive (+) value. However if the volume is already
at maximum due to the EG settings etc., it will not be possi-
ble to increase the volume any further. If you have set this
parameter to a negative (–) value, pressing down on the
keyboard will decrease the volume.
LFO1 Mod. (LFO1 Modulation)
Intensity (LFO1 Intensity)
These parameters let you use "OSC1 LFO1" (5.3–1) to con-
trol the oscillator 1 volume.
Negative (–) values will invert the LFO waveform.
AMS (LFO1 AMS) [Off, (PEG, FEG, AEG, KT, EXT)]
Selects a source that will control the depth by which "OSC1
LFO1" will modulate the volume of oscillator 1 ( p.206
"AMS List").
Int. (AMS Intensity)
Specifies the depth and direction of the effect that "OSC1
LFO1" will have on the volume of oscillator 1. Negative (–)
values will invert the LFO waveform.
LFO2 Mod. (LFO2 Modulation)
Intensity (LFO2 Intensity)
AMS (LFO2 AMS) [Off, (PEG, FEG, AEG, KT, EXT)]
Int. (AMS Intensity)
Specifies the depth and direction of the effect that "OSC1
LFO2"(5.3–2) will have on the volume of oscillator 1. Refer
to the preceding sections "LFO1 Mod. (LFO1 Modulation)."
5.1–2c: UTILITY
"Write Program" (1.1–1d), "Copy Oscillator," "Swap
Oscillator" (2.1–1d)
[–99...+99]
Note-on
Note-off
Strongly played
[Off, (PEG, FEG, EXT)]
[–99...+99]
[–99...+99]
[–99...+99]
[–99...+99]
[–99...+99]