2: Arp. A (Arpeggiator A); 3: Arp. B (Arpeggiator B) - Korg Triton-Rack Parameter Manual

Example 1)
1 Set the "MIDI Channel" (3.1–1a) of timbres 1 and 2 to
Gch, and set "Status" (3.1–1a) to INT.
2 Assign arpeggiator A to timbre 1 and arpeggiator B to
timbre 2, and check "Arpeggiator Run" (1.1–4a/5a, 6.1–
1a).
3 Set the MIDI channel of the external MIDI device trans-
mitting the note data to match the Global MIDI channel
"MIDI Channel" (GLOBAL 2.1–1a).
4 When the [ARP ON/OFF] key is off, playing the key-
board of the connected MIDI device will sound timbres 1
and 2 simultaneously (Layer).
When the [ARP ON/OFF] key is on, playing the key-
board of the connected MIDI device will cause arpeggia-
tors A and B to independently control and play timbres 1
and 2 respectively.
Trigger Arpeggiator Pattern - A
= Gch A
Arpeggiator
Trigger
Pattern - B
= Gch B
Example 2)
1 The "MIDI Channel" (3.1–1a) of timbres 1, 2, 3, 4, and 5
are set respectively to Gch, Gch, 02, Gch, and 03. Their
"Status" (3.1–1a) is set respectively to INT, Off, INT, Off,
and INT.
2 Assign arpeggiator A to timbres 2 and 3, assign arpeggia-
tor B to timbres 4 and 5, and check "Arpeggiator Run"
(1.1–4a/5a, 6.1–1a).
3 Set the MIDI channel of the external MIDI device trans-
mitting the note data to match the Global MIDI channel
"MIDI Channel" (GLOBAL 2.1–1a).
4 When the [ARP ON/OFF] key is off, playing the key-
board of a connected MIDI device will sound only timbre
1. Timbres 2 and 4 are receiving the Gch, but they will not
sound since their "Status" is Off.
When you turn on the [ARP ON/OFF] key, arpeggiator
A will operate for timbres 2 and 3, and arpeggiator B will
operate independently for timbres 4 and 5. (Arpeggiators
A and B are triggered by receiving note data on any MIDI
channel of an assigned timbre, but in this example they
are being triggered from the Gch.)
When you play the keyboard of a connected MIDI
device, arpeggiator A will operate for timbres 2 and 3,
but only timbre 3 whose "Status" is INT will sound. Sim-
ilarly, arpeggiator B will operate for timbres 4 and 5, but
only timbre 5 whose "Status" is INT will sound.
In this way, you can make settings so that a timbre does
not sound when the arpeggiator is off, but sounds only
when the arpeggiator is on.
Trigger Arpeggiator Pattern - A
A
= Gch, Ch2
Pattern - B
Arpeggiator
Trigger
B
= Gch, Ch3
6.1–1c: UTILITY
"Write Combination," "Solo Selected Timbre" (1.1–1d)
For details on how to select the desired utility function, refer
to "PROG 1.1–1d: UTILITY."
44
Arpeggiator
Assign
A Timbre 1 MIDI Ch=Gch Status=INT
B Timbre 2 MIDI Ch=Gch Status=INT
Arpeggiator
Assign
Off Timbre 1 MIDI Ch=Gch Status=INT
A Timbre 2 MIDI Ch=Gch Status=Off
A Timbre 3 MIDI Ch=2ch Status=INT
B Timbre 4 MIDI Ch=Gch Status=Off
B
Timbre 5 MIDI Ch=3ch Status=INT
Copy Arpeggiator
This command copies arpeggiator settings.
1 Select "Copy Arpeggiator" to access the dialog box.
2 In "From" select the copy source (mode, bank, number)
arpeggiator.
If you are copying from Combination, or Multi mode,
select either A or B to if you wish to copy settings from
only one arpeggiator, or select A&B if you wish to copy
the settings of both arpeggiators.
3 If you are copying from a Program, or are copying either
A or B from Combination, or Multi mode, select either A
or B as the "To" copy destination.
Pattern - A
4 To execute the Copy Arpeggiator command, press the
Pattern - B
[F8] ("OK") key. To cancel without executing, press the
[F7] ("Cancel") key.
6.1–2: Arp. A
6.1–3: Arp. B
The Arp. A pages you make settings for arpeggiator A. The
Arp. B pages you make settings for arpeggiator B.
You can also use Utility "Copy Arpeggiator" (6.1–1c) to
copy settings from another mode such as Program
mode.
6.1–2a
6.1–2(3)a: Arpeggiator-A(B) Setup
Pattern*
Octave*
Reso (Resolution)*
Gate
Velocity
Swing
Sounded by normal Sort*
keyboard playing
Does not sound
Latch*
Pattern - A
Key Sync.*
Does not sound
Pattern - B
Keyboard*
These parameters are the arpeggiator A settings for the com-
bination.
( PROG 6.1: Ed–Arp.)
* These parameters can also be set in "1.1–4: Arp. A, 1.1–5:
Arp. B"
6.1–2(3)b: UTILITY
"Write Combination," "Solo Selected Timbre" (1.1–1d),
"Copy Arpeggiator" (6.1–1c)
(Arpeggiator A)
(Arpeggiator B)
[P000...P004, U000(I-A/B)...U327(E-H)]
[ , ,
[000...100%, Step]
[001...127, Key, Step]
[–100...+100%]
6.1–2b
[1, 2, 3, 4]
, , , ]
[Off, On]
[Off, On]
[Off, On]
[Off, On]