014: St.decimator (Stereo Decimator); 015: St.analogrecd (Stereo Analog Record) - Korg Triton-Rack Parameter Manual

014: St.Decimator
(Stereo Decimator)
This effect creates a rough sound like a cheap sampler by low-
ering the sampling frequency and data bit length. You can
also simulate noise unique to a sampler (aliasing).
Stereo In - Stereo Out
Left
Pre LPF Resolution
Decimator
D -mod
Sampling Frequency
LFO
Decimator
Pre LPF Resolution
Right
Pre LPF
a Selects whether the harmonic noise caused by a decrease in sam-
pling frequency is generated or not
High Damp
b
Sets the ratio of cut of the high range
Fs (Sampling Frequency)
Sets the sampling frequency
(Source)
c
Selects the modulation source of the sampling frequency
(Amount)
Sets the modulation amount of the sampling frequency
Resolution
d
Sets the data bit length
Level (Output Level)
Sets the output level
(Source)
e
Selects the modulation source for the output level
(Amount)
Sets the modulation amount of the output level
lfoF (LFO Frequency)
Sets the LFO speed
(Source)
f
Selects the modulation source of LFO speed
(Amount)
Sets the modulation amount of LFO speed
Depth
Sets the depth of the sampling frequency LFO modulation
(Source)
g
Selects the LFO modulation source of the sampling frequency
(Amount)
Sets the LFO modulation amount of the sampling frequency
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
h
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
a: Pre LPF
If a sampler with a very low sampling frequency receives very
high-pitched sound that could not be heard during playback, it
could generate pitch noise that is unrelated to the original sound.
Set "Pre LPF" to ON to prevent this noise from being generated.
If you set the "Fs" to about 3kHz and set "Pre LPF" to OFF, you
can create a sound like a ring modulator.
d: Resolution, e: Output Level
If you set a smaller value for the "Resolution" parameter, the
sound may be distorted. The volume level may also be changed.
Use "Level" to adjust the level.
015: St.AnalogRecd
This effect simulates the noise caused by scratches and dust
on analog records. It also reproduces some of the modulation
caused by a warped turntable.
Wet / Dry
High Damp Output Level
High Damp Output Level
Wet / Dry
Off, On
0...100%
1.00k...48.00kHz
Off...Tempo
–48.00k...+48.00kHz
4...24
0...100
,
Off...Tempo
–100...+100
0.02...20.00Hz
Off...Tempo
–20.00...+20.00Hz
0...100
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100 b: Flutter
This parameter enables you to set the depth of the modulation
caused by a warped turntable.
h: ClickLvl
This parameter enables you to set the level of the click noise that
occurs once every rotation of the turntable. This simulation repro-
duces record noise, and the noise generated after the music on a
vinyl record finishes.
(Stereo Analog Record)
Stereo In - Stereo Out
Left
EQ Trim Pre EQ
Analog Record
Simulation
EQ Trim Pre EQ
Right
Speed
a
Sets the r.p.m. of a record
Flutter
b
Sets the modulation depth
Pre EQ Trim
c
Sets the EQ input level
EQ (Pre EQ Cutoff)
Sets the EQ center frequency
Q
d
Sets the EQ band width
G (Gain)
Sets the EQ gain
Noise Density
e
Sets the noise density
Noise Tone
f
Sets the noise tone
NoiseLvl (Noise Level)
Sets the noise level
(Source)
g
Selects the modulation source for the noise level
(Amount)
Sets the modulation amount of the noise level
ClickLvl (Click Level)
Sets the click noise level
(Source)
h
Selects the modulation source for the click noise level
(Amount)
Sets the modulation amount of the click noise level
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
i
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
Wet / Dry
Wet / Dry
33 1/3, 45, 78RPM
0...100
0...100
300...10.00kHz
0.5...10.0
–18.0...+18.0dB
0...100
0...100
0...100
Off...Tempo
–100...+100
0...100
,
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
159