Please Note When Installing An Option Board/Memory; Checking After Installation; Caution When Purchasing Dram Simm Modules - Korg Triton-Rack Parameter Manual

DRAM SIMM (sample data memory modules)
These can be used as sample data memory. Up to two 72-pin
DRAM SIMM (either 16 Mbyte or 32 Mbyte) modules can be
installed, providing a maximum of 64 Mbytes. ( "Caution
when purchasing DRAM SIMM modules")
DRAM SIMM boards are not a manufacturer option.
Please purchase commercially-available boards that are
sold for use in computers.
In order to achieve the maximum 96 Mbyte capacity,
you will need to remove the 16 Mbyte DRAM SIMM
that is standard, and install three 32 Mbyte DRAM
SIMM boards.
The memory banks and sampling time will depend on
the capacity of the DRAM SIMM boards you install,
and on the slot locations. ( p.77)
Please note when installing an option
board/memory
•Avoid touching exposed metal edges of the circuit
board, or portions that need not be handled during
installation.
• So that static electricity in your body does not damage
the electronic components, touch the ground wire of a
grounded device or an unpainted metallic component
to discharge any static electricity in your body before
installing an option board or memory. Internal compo-
nents of the TRITON-Rack and of the option/memory
boards may be damaged by static electricity.
• Follow the installation procedure, and be sure that each
part is installed correctly and in the correct orientation.
• Please use care in handling option boards/memory.
Dropping them or applying pressure to them may
damage the components.
• Be careful not to lose the screws (and washers) that you
remove.
• Do not use screws other than those that are installed in
the option board/memory and the TRITON-Rack.
Using screws of a different shape or length may dam-
age the unit or cause it to malfunction.
• Be sure to firmly tighten the screws used for attach-
ment.
• Be sure that the option board/memory is inserted cor-
rectly into the connector or slot. After installation, be
sure to check that the board is installed correctly. If the
board is not inserted all the way, faulty contact or
power supply shorts can occur, making the unit mal-
function.
• Be careful not to drop parts or the option board/mem-
ory into the inside of the instrument.
If you are unable to retrieve a screw or part that was
dropped inside the instrument, please contact your
local Korg distributor.
244

Checking after installation

When the TRITON-Rack is turned on, the currently
installed option boards/memory will be shown in the
LCD screen.
After installing an option board/memory, be sure to
turn on the power and make sure that the option
board/memory that you installed is displayed in the
LCD screen.
If it is not displayed, the installation may not have been
performed correctly. Check once again that the board is
installed correctly.
If you have any questions regarding installation, please
contact your local Korg distributor .
OPTIONS
EXB-MOSS: The EXB-MOSS option is installed.
EXB-SCSI: The EXB-SCSI option is installed.
EXB-DI: The EXB-DI option is installed.
EXB-mLAN: The EXB-mLAN option is installed
SIMM
Slot 1...3 (** MB): SIMM's are installed in SIMM slots 1–3.
The capacity of each SIMM is shown in parentheses. When
shipped from the factory, a 16 MB SIMM is already installed
in SIMM slot 1.
EXB-PCM
Slot 1...8 (****): PCM expansion boards are installed in EXB-
PCM series slots 1–8. The type of each board is shown in
parentheses.
Caution when purchasing DRAM SIMM
modules
Some commercially available DRAM SIMM modules
cannot be used on the TRITON-Rack. Before you pur-
chase memory modules, please check the following
points.
Types of DRAM SIMM modules that can be used on the
TRITON
• 72-pin 16 Mbyte or 32 Mbyte
• Access time of 60 ns or less
• Address input 11 bit (A0–A10)
• Power supply voltage 5 V
DRAM SIMM modules that meet the above requirements
can be used.
If you have any questions regarding the type of DRAM
SIMM modules that can be used, please contact your local
Korg distributor .