2: Prog - Korg Triton-Rack Parameter Manual

3 Select the data that you wish to copy.
All: will copy all pattern data and musical data.
"Without Patterns": Multi settings other than pattern
data and RPPR settings will be copied.
4 To execute the Copy Multi operation, press the [F8]
("OK") key. To cancel without executing press the [F7]
("Cancel") key. If you execute "All," all settings and pat-
tern data of the currently selected multi will be deleted
and replaced by the copy source data. If you execute
"Without Patterns," all setting data other than the pat-
tern data and RPPR settings of the currently selected
multi will be deleted and replaced by the copy source
data.
Copy From Combi (Copy from Combination)
This command copies the parameters of the specified combi-
nation to the currently selected multi.
1 Select "Copy From Combi" to access the dialog box.
2 In "Combi," select the copy source destination.
3 If you check "with Effects," the insertion effect, master
effect, and master EQ settings will also be copied.
4 In "To," select the copy destination tracks (1–8 or 9–16).
5 To execute the Copy From Combi command, press the
[F8] ("OK") key. To cancel, press the [F7] ("Cancel") key.
Be aware that when you execute this command, the set-
ting data of the currently selected multi will be erased,
and overwritten by the data of the selected combination.
Load Template Multi
This command loads a template multi into the multi mode.
The TRITON-Rack contains sixteen preset template multis
(P00–15) with program and effect settings appropriate for
various styles of music. You can also create sixteen user tem-
plate multis (U00–15) with the programs, track parameters,
and effects etc. that you use frequently. ( "Save Template
Multi")
1 Select "Load Template Multi" to access the dialog box.
2 In "From," specify the template multi that you wish to
load.
3 To load the template multi, press the [F8] ("OK") key. To
cancel, press the [F7] ("Cancel") key. When you execute
the command, multi setting data other than pattern data
and RPPR will be copied.
Save Template Multi (Save as User Template Multi)
This command saves the program selections, track parame-
ters, and effect settings etc. of the multi as a user template
multi U00–15.
1 Select "Save Template Multi" to access the dialog box.
2 In "To," specify the user template multi (U00–15) in
which the data will be saved.
3 To save the template multi, press the [F8] ("OK") key. To
cancel, press the [F7] ("Cancel") key. Be aware that when
you execute this command, all setting data of the save
destination User Template Multi will be erased and
rewritten.
Rename Track
Selects "Rename Track," access the dialog box and rename
the selected multi. Up to sixteen characters can be input.
( BG p.38)
GM Initialize
This command resets each track to settings appropriate for
GM. ( See the table at the bottom of the next page.)
When a GM System On message is received from an
external device in Multi mode, the TRITON-Rack will
be reset to GM settings in the same way as when this
command is executed. (However in these cases, the var-
ious 7.3: MasterFx parameters will not be reset.)
1.1–2: Prog..8
(Track Program T01...08)
1.1–3: Prog..16
(Track Program T09...16)
Specifies the program used by each track.
1.1–2a
1.1–2b
1.1–2c
1.1–2(3)a: Track Number & Category
Track Number & Category
This shows the track number and the abbreviated name of
the program category.
1.1–2(3)b: Program Select
Program Select
[I-A...F/E-A...H 000...127, G...g 001...128: name]
Selects the program used by each track.
If the "Status" (3.1–1a/2a) is EX2, a "–" will be displayed
before the program number.
By holding down the [TIMBRE/TRACK] key and
pressing a [F1](1/9)–[F8](8/16) key you can move to
the corresponding track "T1"–"T16."
The program bank can also be selected directly by using
the [A]–[H] keys and the [BANK] key.
You can also use the "Select by Category" utility to
select programs by category.
If the "Status" (3.1–1a/2a) is either INT or BTH, pro-
grams can be selected by receiving MIDI program
change messages. Also, when the multi is changed,
tracks whose "Status" is EXT, EX2 or BTH will transmit
the bank and program numbers via MIDI. Tracks
whose "Status" is EX2 will transmit the bank number
that was selected in the "Bank(EX2) LSB," "Bank(EX2)
MSB" (3.1–1a).
1.1–2d
51