Prog 7.2: Ed-Insertfx; 1: Setup; 2: Ifx 1; 3: Ifx 2 - Korg Triton-Rack Parameter Manual

PROG 7.2: Ed–InsertFX
7.2–1: Setup
Here you can select the type of each insert effect, turn it on/
off, and make chain settings.
The direct sound (Dry) of an insert effect is always stereo
input and output. The input/output of the effect sound
(Wet) will depend on the effect type ( p.142).
7.2–1a
7.2–1a: InsertFX Setup
IFX1 On/Off — IFX5 On/Off
Selects the insert effect on/off.
When this is Off, the input will be output without change.
(For 000: No Effect, on/off will produce the same result.)
Separately from this setting, you can use control change
#92 to turn off all insert effects together. A value of 0
will be off, and a value of 1–127 will be the original set-
ting. This message is received on the global MIDI chan-
nel specified by "MIDI Channel" (GLOBAL 2.1–1a).
Insert Effect 1, 5
Insert Effect 2, 3, 4
Selects the type of each insert effect.
For "Insert Effect 1" and "Insert Effect 5" you can select from
90 types of effect: 000: No Effect – 089: Reverb-Gate. Dou-
ble-size effects cannot be used.
For "Insert Effect 2," "Insert Effect 3" and "Insert Effect 4"
you can select from 103 types of effect: 000: No Effect – 102:
Hold Delay.
If you select a double-size effect, the next insert effect will be
unavailable for use. For example if you select a double-size
effect for IFX2, IFX3 cannot be used. A maximum of two
double-size effects can be used (normal size for IFX1, double
size for IFX2 and IFX4) ( p.142).
These effects can also be selected by category in Utility
"Select by Category" (7.2–1b).
Chain
Selects "chain" on/off for each insert effect.
For example if "Chain" for IFX1 is set to
IFX2 will be connected in series. If "BUS Select" (7.1–1a) is
set to IFX1, IFX1 and IFX2 will be inserted in series.
A maximum of five insert effects (IFX1–IFX5) can be inserted
in series. When effects are chained, the "Pan (CC#8)," "BUS
Select," "S1 (Send1(MFX1))" and "S2 (Send2(MFX2))" set-
tings that follow the last IFX in the chain will be used.
Pan(CC#8) (Post IFX Pan CC#8)
Sets the pan after the sound has passed through the insert
effect. This setting is valid only when the following "BUS
Select" is set to L/R ( p.145).
CC#8 will control.
28
7.2–1b
[Off, ON]
[000...089: name]
[000...102: name]
[ (Off), (ON)]
(ON), IFX1 and
[L000...C064...R127]
BUS Select [L/R, 1, 2, 3, 4, 1/2, 3/4, Off]
Specifies the bus to which the sound will be sent after pass-
ing through the insert effect. Normally you will set this to L/
R. If you wish to output to AUDIO OUTPUT (INDIVID-
UAL), set this to 1, 2, 3, 4, 1/2, or 3/4. The Off setting is used
when you wish to use "S1 (Send1(MFX1))" and "S2
(Send2(MFX2))" and in addition connect to the master
effects in series.
S1 (Send1 (MFX1))
S2 (Send2 (MFX2))
Sets the send levels to the master effects 1 and 2 for the
sound that has passed through the insert effect. These set-
tings are valid when "BUS Select" (7.1–1a) has been set to L/
R or Off.
Control change CC#93 will control the Send 1 level, and
control change CC#91 will control the Send 2 level.
These messages are received on the global MIDI chan-
nel specified by "MIDI Channel" (GLOBAL 2.1–1a).
7.2–1b: UTILITY
"Write Program" (1.1–1d), "Copy Insert Effect," "Swap
Insert Effect" (7.1–1c)
Select by Category
Selects insert effects by category.
For the procedure, refer to "Select by Category" ( p.2).
This command can be used when selecting "Insert
Effect 1"–"Insert Effect 5."
7.2–2: IFX 1
7.2–3: IFX 2
7.2–4: IFX 3
7.2–5: IFX 4
7.2–6: IFX 5
Here you can set the effect parameters for the IFX 1/2/3/4/
5 that were selected in the Setup page ( p.151).
Effect dynamic modulation (Dmod) is controlled on the
global MIDI channel "MIDI Channel" (GLOBAL 2.1–
1a). ( p.211 "D.mod")
[000...127]
[000...127]
7.2–2a