Combi 7.3: Ed-Masterfx; 1: Setup; 2: Mfx1 (Master Effect1); 3: Mfx2 (Master Effect2) - Korg Triton-Rack Parameter Manual

COMBI 7.3: Ed–MasterFX
For details on master effects, refer to p.146.
7.3–1: Setup
Here you can select the type of each master effect, turn it
on/off, and make chain and master EQ settings.
With the exception of "MFX1 Control Ch," "MFX2 Control
Ch," and "MEQ Control Ch," this is the same as in Program
mode. ( PROG 7.3: Ed-MasterFX)
7.3–1a
7.3–1b
7.3–1a: MasterFX Setup
MFX1 On/Off, MFX2 On/Off
Master Effect 1, 2
Rtn 1, 2 (Return 1, 2)
These are the same as in Program mode. Refer to "PROG
7.3-1: Setup." However, the master effects will be controlled
on the "MFX 1, 2 Control Ch" MIDI channel, unlike in Pro-
gram mode.
The control changes used are the same as in Program mode.
MFX 1, 2 Control Ch
Selects the MIDI channel that will control dynamic
modulation (Dmod) for the master effects.
G ch: The global MIDI channel "MIDI Channel" (GLOBAL
2.1-1a) will be used for control. Normally you will set this
parameter to G ch.
7.3–1b: MasterFX Chain
MFX Chain
Direction (Chain Direction)
Signal (Chain Signal)
Level (Chain Level)
These are the same as in Program mode. ( "PROG 7.3–1:
Setup")
7.3–1c: Master EQ Gain [dB]
Low
Mid
High
These are the same as in Program mode. ( "PROG 7.3–1:
Setup")
7.3–1d: MEQ Ctrl
MEQ Ctrl (MEQ Control Ch)
Selects the MIDI channel that will control dynamic
modulation (Dmod) for the master EQ.
48
7.3–1d 7.3–1c 7.3–1e
[Off, ON]
[000...089: name]
[000...127]
[Ch001...16, G ch]
[MFX1→MFX2, MFX2→MFX1]
[LR Mix, L Only, R Only]
[000...127]
[–18.0...+18.0]
[–18.0...+18.0]
[–18.0...+18.0]
[Ch01...16, G ch]
G ch: The global MIDI channel "MIDI Channel" (GLOBAL
2.1–1a) will be used for control. Normally you will set this
parameter to G ch.
7.3–1e: UTILITY
"Write Combination," "Solo Selected Timbre" (1.1–1d),
"Select by Category" (PROG 7.3–1d)
Copy Master Effect
( PROG 7.3–1d)
Note, the MIDI control channel that is specified by "MFX1, 2
Control Ch" (7.3–1a) will not be copied.
Swap Master Effect
( PROG 7.3–1d)
Note, the MIDI control channel that is specified by "MFX1, 2
Control Ch" (7.3–1a) will not be swapped.
7.3–2: MFX1
(Master Effect1)
7.3–3: MFX2
(Master Effect2)
Here you can set the parameters for the "Master Effect1"
and "Master Effect2" effects that were selected in the Setup
page ( p.151).
7.3–2(3)a: UTILITY
"Write Combination" (1.1–1d)
7.3–4: MEQ
(Master EQ)
The master EQ is a three-band stereo EQ. It is located imme-
diately before the AUDIO OUTPUT (MAIN OUT) L/
MONO and R from the L/R bus, and adjusts the overall
tonal character of the sound ( p.203).
7.3–4a: UTILITY
"Write Combination" (1.1–1d)
7.3–2a
7.3–4a