Mitsubishi Electric MELSEC iQ-F Series User Manual page 270

Requirements for Low Voltage Directive (LVD) compliance
The following products have shown compliance through direct testing (of the identified standards below) and design analysis
(through the creation of a technical construction file) to the European Low Voltage Directive (2014/35/EU) when used as
directed by the appropriate documentation.
■Product compatibility
Type: Programmable controller (open-type device)
from October 1st, 2014
from May 1st, 2016
from October 1st, 2016
from January 1st, 2019
from October 1st, 2019
from October 1st, 2021
*1 Area-specific model
For the products above, programmable controllers manufactured
before March 31st, 2018 are compliant with EN61131-2:2007.
Programmable controllers manufactured after April 1st, 2018 are compliant with EN61131-2: 2007 and IEC 61010-2-201:
*2
2018.
*2 For some models, programmable controllers manufactured in March, 2018 are compliant with LVD directive successively.
Compliance with LVD directive
EN61131-2:2007 Programmable controllers
• Equipment requirements and tests
EN IEC 61010-2-201:2018
Safety of electrical equipment for measurement, control, and test
Caution for compliance with EC Directive
• Please use the FX5 CPU modules while installed in conductive shielded control panels under a general industrial
environment.
• Please use the programmable controller while installed within a conductive shielded control panel. Please secure the
control box lid to the control box (for conduction). Installation within a control panel greatly affects the safety of the system
and aids in shielding noise from the programmable controller.
• For the control panel, use the product having sufficient strength, fire protectiveness and shielding property to an installation
environment.
• 24VDC of the power supply must be supplied from the circuit double/reinforced insulated from the main power supply
(MAINS).
• For the AC power supply input cable of modules manufactured in or before November 2020 (serial number 20Y****) shown
below, wind a ferrite core around it once near the module.
Item
Ferrite core used in tests by Mitsubishi Electric
Target modules
• When not using the peripheral connector during operation, close the peripheral connector cover. In addition, if there is a
possibility that the built-in Ethernet communication connector may be touched in operation, be sure to eliminate the static
electricity or attach an Ethernet cap
*1 Reference product: MJ-JP68K manufactured by JST Mfg. Co., Ltd.
APPX
268
Appendix 2 Standards
FX5U-32MR/ES, FX5U-32MT/ES, FX5U-32MT/ESS, FX5U-64MR/ES, FX5U-64MT/ES, FX5U-64MT/ESS, FX5U-80MR/
ES, FX5U-80MT/ES, FX5U-80MT/ESS, FX5-8EYR/ES, FX5-16EYR/ES, FX5-32ER/ES, FX5-32ET/ES, FX5-32ET/ESS,
FX5-1PSU-5V
FX5U-32MR/DS, FX5-32ER/DS
FX5U-64MR/DS, FX5U-80MR/DS, FX5-16ER/ES
FX5UC-32MR/DS-TS, FX5-C16EYR/D-TS
FX5UJ-24MR/ES FX5UJ-24MT/ES FX5UJ-24MT/ESS, FX5UJ-40MR/ES FX5UJ-40MT/ES FX5UJ-40MT/ESS, FX5UJ-
60MR/ES FX5UJ-60MT/ES FX5UJ-60MT/ESS
FX5S-30MR/ES, FX5S-30MT/ES, FX5S-30MT/ESS, FX5S-40MR/ES, FX5S-40MT/ES, FX5S-40MT/ESS, FX5S-60MR/
ES, FX5S-60MT/ES, FX5S-60MT/ESS, FX5S-80MR/ES
*1
to prevent the influence of static electricity.
*1 *1
, FX5S-80MT/ES
Remarks
The equipment has been assessed as a component for fitting in a suitable
control box which meets the requirements of EN61131-2:2007.
The equipment has been assessed as a component for fitting in a suitable
control box which meets the requirements of EN IEC 61010-2-201:2018.
Description
E04SR401938 (SEIWA ELECTRIC MFG. CO., LTD.)
FX5UJ-40MR/ES FX5UJ-40MT/ES FX5UJ-40MT/ESS
FX5UJ-60MR/ES FX5UJ-60MT/ES FX5UJ-60MT/ESS
*1
, FX5S-80MT/ESS