Menu 0: Basic Parameters - Emerson SP1201 Installation Manual

Safety Product
Introduction
Information information
9.2

Menu 0: Basic parameters

Table 9-2 Unidrive SP Regen menu 0 parameter descriptions
Parameter
0.00 xx.00
0.01 Voltage setpoint
0.02 Voltage controller Kp gain
0.03 Enable motor drive
0.04 DC bus voltage
0.05 Output / supply voltage
0.06 Regen drive status
0.07 Regen restart mode
0.08 Close soft start contactor
0.09 Soft start contactor closed
0.10 Power feed forward compensation
0.11 Output / supply frequency
0.12 Current magnitude
0.13 Active current
0.14 Output / supply power
0.15 Reactive power
0.16 Input inductance
0.17 Reactive current reference
0.18 Positive logic select
0.19 T7 analogue input 2 mode
0.20
T7 analogue input 2 destination
0.21 T8 analogue input 3 mode
0.22 Not used
0.23 Not used
0.24 Not used
0.25 Not used
0.26 Not used
0.27
Not used
0.28 Not used
SMARTCARD parameter data
0.29
previously loaded
0.30 Parameter cloning
0.31 Drive voltage rating
0.32 Maximum Heavy Duty current rating
0.33 Not used
0.34 User security code
0.35 Serial mode
0.36 Baud rate
0.37 Serial address
0.38 Current controller Kp gain
0.39 Current controller Ki gain
0.40 Not used
0.41 Maximum switching frequency
0.42 Not used
0.43 Not used
0.44 Not used
0.45 Thermal time constant
0.46 Regen drive rated current
0.47 Not used
0.48 User drive mode
0.49 Security status
0.50 Software version
0.51 to
Not used
0.59
RW Read / Write RO Read only
FI Filtered DE Destination
* Modes 1 and 2 are not user saved, Modes 0, 3 and 4 are user saved
Unidrive SP Regen Installation Guide
Issue Number: 2
System Mechanical Electrical
design installation installation
Range( )
0 to 32,767
{ 3.05 } 0 to DC_VOLTAGE_SET_MAX V
{ 3.06 } 0 to 65535
{ 3.09 } OFF (0) or On (1)
{ 5.05 } 0 to +DC_VOLTAGE_MAX V
{ 5.02 } 0 to AC_VOLTAGE_MAX V
{ 3.03 } 0 to 15
{ 3.04 } 0 to 2
{ 3.07 } OFF (0) or On (1)
{ 3.08 } OFF (0) or On (1)
{ 3.10 } ±100.0 %
{ 5.01 } ±100.0 Hz
{ 4.01 } 0 to DRIVE_CURRENT_MAX A
{ 4.02 } ±DRIVE_CURRENT_MAX A
{ 5.03 } ±POWER_MAX kW
{ 3.01 } ±POWER_MAX kVAR's
{ 3.02 } 0.000 to 500.000 mH
{ 4.08 } ±REGEN_REACTIVE_MAX %
{ 8.29 } OFF (0) or On (1)
0-20 (0), 20-0 (1), 4-20.tr (2), 20-4.tr (3),
{ 7.11 }
4-20 (4), 20-4 (5), VOLt (6)
{ 7.14 } Pr 0.00 to 21.51
0-20 (0), 20-0 (1), 4-20.tr (2), 20-4.tr (3),
{ 7.15 } 4-20 (4), 20-4 (5), VOLt (6), th.SC (7),
th (8), th.diSP (9)
{ 11.36 } 0 to 999
nonE (0), rEAd (1), Prog (2), AutO (3),
{ 11.42 }
boot (4)
{ 11.33 } 200 (0), 400 (1), 575 (2), 690 (3)
{ 11.32 } 0.00 to 9999.99A
{ 11.30 } 0 to 999
{ 11.24 } AnSI (0), rtU (1)
300 (0), 600 (1), 1200 (2), 2400 (3), 4800 (4),
{ 11.25 } 9600 (5), 19200 (6), 38400 (7),
57600 (8)*, 115200 (9)* *Modbus RTU only
{ 11.23 } 0 to 247
{ 4.13 } 0 to 30,000
{ 4.14 } 0 to 30,000
{ 5.18 } 0 to 5 (3, 4, 6, 8, 12, 16 kHz)
{ 4.15 } 0.0 to 400.0
{ 5.07 } 0 to RATED_CURRENT_MAX A
OPEn LP (1), CL VECt (2),
{ 11.31 }
SErVO (3), rEGEn (4)
{ 11.44 } L1 (0), L2 (1), Loc (2)
{ 11.29 } 1.00 to 99.99
Uni Unipolar Bi Bi-polar
NC Not cloned RA Rating dependent
www.controltechniques.com
Getting
Optimisation Parameters
started
Default( )
700 Vdc
4000
On (1)
VOLt (6)
Pr 3.10
VOLt (6)
nonE (0)
rtU (1)
19200 (6)
1,000
0 (3kHz)
rEGEn (4)
L2 (1)
Bit Bit parameter Txt
PT Protected US
Technical Component
data sizing
Type
0 RW Uni
RW Uni
RW Bi
RO Uni NC
RO Uni FI NC PT
RO Uni FI NC PT
RO Uni NC PT
1 RW Uni
RO Uni NC
RO Uni NC
0.0 RW Bi NC
RO Bi FI NC PT
RO Uni FI NC PT
RO Bi FI NC PT
RO Bi FI NC PT
RO Bi FI NC PT
RO Uni NC PT
0.0 RW Bi
RW Bit
RW Txt
RW Uni DE
RW Txt
0 RO Uni NC PT US
RW Txt NC
RO Txt NC PT
RO Uni NC PT
0 RW Uni NC PT PS
RW Txt
RW Txt
1 RW Uni
45 RW Uni
RW Uni
RW Uni
89.0 RW Uni
RW Uni
RW Txt NC PT
RW Txt
RO Uni NC PT
Text string
User save PS Power down save
Diagnostics
US
US
US
US
PT US
US
PT US
US
*
US
US
US
US
US
US
US
US
PT US
93